Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter
Item N° y0769 Heavy duty plastic servo arms for Smartech 301502 servo, 3 pcs.Heavy duty plastic servo arm with a total l^enght of 50 mm and six mounting positions.Content:Thee peaces
Accelerator-spray is the second component to cure superglue immediately.This set is also particularly suitable for the possible repair of loosened tire/rim gluing!Advantages:Tangible adhesion after a few secondsAromatic solvents and hexane freeSuitable for hobby, craft, industry and householdProcessing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.Contents:Special tire cement ht 4000Spray can activator
Cap screws for 1/5 & 1/6 large scale cars, DIN 912 - 8.8 M5x16 with corresponding external tooth lock washers DIN 679A.The lock washers prevent loosening of the manifold screws.Bag with five each screws and lock washers.Part is delivered in silver or black color from vendor!
Genuine HT spare/option part.Fine pitch gears for layshaft and differential, for competition use in touring car and GT models only. The gears run smoother and quieter than the stock parts, reducing the car's rolling resistance. Only for use with the fine pitch differential ring gear! Module: m=1.Contents:1 piece [INCLUDE]profilverschoben[ENDINCLUDE]
The SPEED TEC EXPERT genuine Zenoah 30,5 cm³ engine is optimized for performance with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust and intake. Piston: weight reduced; skirt shortened; oil rings, piston above and below piston ring tapered and piston dome ground. Crankshaft: The Zenoah 30,5 cm³ SPEED TEC Expert comes with the genuine Zenoah +2 mm stroker crank #577953101. It is adjusted, aligned and balanced. Flywheel: weight reduced and checked for runout. Gaskets: use of premium quality gaskets.To achieve the optimum performance gain of a SPEED TEC EXPERT engine, we recommend the use of a tuned pipe ( to the tuned pipes ).
The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The body shell is vac-formed from 2 mm Lexan. This body shell comes without pre-drilled mounting holes, it can be installed on all FG standard width touring car chassis' with 535 mm wheelbase, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase.Set contains:FG 8180 Body shell set BMW M3 ALMS - 219,95 EURFG 8185/01 Vehicle decals BMW M3 ALMS - 50,50 EURy0683 Large Jägermeister decals - 29,90 EURSurcharge Jägermeister painting + glueing the decals - 195,90 EURRegular price: 496,25 EURThe set is delivered as shown.Required body mounts:Mount front: FG 7020/12 Front bumperRear body mount: FG 7152/01 Rear body mount Side body mount front: FG 7014 Body mountsSide body mount rear: FG 7014 Body mountsMeasures:Length: 890 mmWidth: 392 mmHeight: 260 mmWheelbase: 530 mm
Very high quality 0.25 mm thick gasket. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
y0761 Version:
y0761/02 one pair for approx. 80 mm wide tires+ 2EUR
New highly reinforced MadMax rim with 24 mm hex drive and optimized beadlock rings.20-fold screwed very tough and suitable for all 1/6 &1/5 Carson Wild GP Attack, Losi 5ive-T or Desert Buggy XL and HPI cars.The MadMax Extreme rims are available for either 60 or 80 mm tire width.They come with optimized inner and outer beadlock rings, 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench) and reinforcement rings around the wheel hex.Our shop offers you the choice of economically priced sets of the following combinations:y0761/01 one pair for approx. 60 mm wide tiresy0761/02 one pair for approx. 80 mm wide tires y0761/03 two pairs for approx. 60 mm wide tires y0761/04 one pair each for approx. 60 and 80 mm wide tires
Genuine HT spare/option part. The 20-amp Bigscale switch was specifically designed as a receiver switch for 1/5 and 1/6 cars applications.Note: the electronic switch 20 amp Bigscale delivers the batterys full voltage to the connected receiver. When using 7.4V LiPo batteries receiver and servos must be suitable for this voltage!Using the latest MOSFET technology allows the20 amp Bigscale switch to handle extreme loads, despite its small size.You can even use four very powerful servos which are common in large scale cars without any problems!A blue LED status light clearly displays the activated mode. The 20 amp Bigscale switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period.Properties:Voltage range: 3 to 10 Vmax. Load: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions: L x W x H: 28 x 12 x 11 mmThe electronic 20 Amp Bigscale switch is available with several battery connectors.Contents:1 piece
DVD-set of the touring cars european championship 2005 in Gothenburg/Sweden made by Chris Wright (Rev-Up racing magazine).Highlights:- The opening parade- Footage at track level- Slow motions- Picture-in-picture effects- Jumps- Rolls and so on- New parts- Pit footage of the cars and people- Final run - Award ceremony- Interview with the winnerNumber of DVD's: 2Total currency: about 120Min.Available in PAL and NTSC-Version
Unit price: 179,80 EURSet price: 159,90 EURComplete set of aluminum a-arms, machined from high grade 7075-T6 aluminum, front and rear for Losi 5ive-T, with replaceable bushings.All necessary hardware included. Set of two each top quality front and rear a-arms. Set includes:LO5T055 GPM Aluminum lower front a-arms for Losi 5ive-TLO5T056 GPM Aluminum lower rear a-arms for Losi 5ive-TWeights:Front: 343 grams/pairRear: 323 gram/pair
The use of NGK spark plug caps with noise suppression resistor offers an optimal suppression of RFI in all frequency ranges without negative effects on engine performance.NGK spark plug caps are equipped with a resistor element made of high quality ceramic material. This ensures a constant resistance value with only a slight deviation in overload conditions. Features: Material: phenolic resinType: 90 degreeColor: Black Resistance: 5 kilo ohms RFI suppression: Yes Waterproof: Yes Cable length: Without cable Connection: SAE terminal nut or integrated terminal Features: Compact type; only 31.5 mm high
Race ported top end set for Zenoah G240, G270 and G290 engine.The SPEED TEC EXPERT genuine Zenoah 30,5 cm³ race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intake Piston: Weight reducedSkirt shortenedPiston above and below piston ring tapered and piston dome ground The set includes the following items: Performance-optimized cylinder and piston, piston ring, piston pin, piston pin circlips and cylinder gasket.To achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ( to the tuned pipes ).Each SPEED TEC Tuning cylinder set comes with a small amount of a spec. assembly lube for the installation of piston and piston ring. This spec. lube provides the required lubrication to the engine for the first start and dissolves without residue!Please note: You also need the modified crankshaft # along with the SPEED TEC EXPERT top end set to convert a Zenoah 240/270/290 engine to 30.5 cc.
€229.90*
This website uses cookies to ensure the best experience possible. More information...