y0529 Version:
y0529RL One piece each with right- and left hand thread+ 4.9EUR
Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.This version is for steering rod applications.Sets available:One each with r/h and l/h threadOne x r/h threadOne x l/h thread Please note:We recommend using a nut 4472/03 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment.
y0529_02 Version:
y0529/02R one piece with M8 right thread with 5 mm bore in ball
One pieces of steel ball joint with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.
y0529_01 Version:
y0529/01RL One piece each with right- and left hand thread+ 4.9EUR
Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One each with r/h and l/h threadOne x r/h threadOne x l/h thread
Genuine rc-car-online spare/option part. Foam-Cleaner, special cleaning agent for foam air filter elements and GPM coverThe foam-Cleaner is specially designed for RC foam air filters, as well as covers for starter, filter and shocks. Removes reliably dirt, mud, dust, old filter oil, and sand particles and ensures optimum air flow. After cleaning please oil the air filter with air filter oil with order-no. y0284 for foam filters before re-use. Routinely cleaning of filters protects against premature wear and extends engine life!Use: apply cleaner to filter/cover, wait for some minutes and rinse with warm water. Let the parts dry before re-use.Bottle with 500 ml.Contents:1 piece
Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece
y0521 Version:
y0521/01 - for M8 wheel shafts+ 3EUR
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
Regular price: 9,70 EUROffer price: 4,90 EURy0529/01 - Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo and other applications.Set contents:One each with M4 right hand thread or one each M4 with left hand threadPlease note:We recommend using a nut 54374 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment. y0529 - Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ballSteel ball joints 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.Set contents:One each with M6 right hand thread or one each M6 with left hand threadPlease note:We recommend locking the ball joints using M6 low height nuts y0888 or y0889 to prevent the linkage from loss of adjustment. y0529/02 - Steel ball joints M8 r/h or l/h thread, 5 mm bore in ball One pieces of steel ball joints with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.Please note:We recommend using a nut 4472/02 or 4472/03 for locking the thread ball joint to prevent the linkage from loss of adjustment.