12 products found for "y0429"

rc-car-online - Home

y0499 mf-RaceLine microphone filter, 1 pce.

Fits Lauterbach airbox, mf-RaceLine airbox and the new FG airboxes with the numbers 9466 and 9467. Also for all other airboxes, where a filter with an inner diameter of about 35 mm is required (stretches up to 55 mm).

€5.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y0469 Special stuffed stroker crankshaft for 30.5 cm³

Genuine HT spare/option part. Stuffed stroker crankshaft. Spare part for the 30.5 cc big bore kit y0466.Contents:1 piece

€89.90*

y0729 Gas-nitrited tuning clutch bell for HPI Baja, Carson Wild GP Attack models, 1 pce.

Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

€49.90*

y0929 HT Aluminum limited slip differential conversion kit for Carson Gas Devil + CRT 4x4, Conrad Hell Devil, Smartech Titan

Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece

€129.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/01 - 180 mm

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

€5.90*

Heat shrink tube for batteries, 120 x 70 mm - 5 pce

y0429 Color: y0433 black+ 1EUR

E.g. fits on 5er batterie pack in Sub C size.Of course, also for various other purposes be used.Size:Width 120mmHeight 70mm Available in the colors:Yellow, Black, Transparent Blue and Transparent Yellow.Shipped 5 pieces, without accessories

Content: 60 Zentimeter (€4.83* / 100 Zentimeter)

Variants from €1.90*

€2.90*

Low voltage failsafe module, y0423 - 1pce.

To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.

€49.30*

y0529 Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ball

y0529 Version: y0529L One piece left hand thread+ 1EUR

Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.This version is for steering rod applications.Sets available:One each with r/h and l/h threadOne x r/h threadOne x l/h thread Please note:We recommend using a nut 4472/03 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment.

Variants from €5.90*

€6.90*

y0425/03 Parallel Y-harness

Genuine rc-car-online spare/option part. Optional equipment part for Axial Jeep Wrangler 4WD 1/6.Features:14 AWG to 10 AWGEC5 connectorsContent:1 piece

€19.80*

y0425/02 Y-harness current, universal connector

Genuine rc-car-online spare/option part. Total length:approx. 200 mmContents:1 piece

€14.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y0428/03 Extension cable universal

y0428_03 Length: y0428/02 - 300 mm+ 1EUR

In case the battery cable is not long enough.Contents:1 piece

€9.90*

y0425/01 Y-harness, silicone insulated, universal/JR

Genuine HT spare/option part. The Y-harness is required for running two servos on a single receiver channel. Top quality heavy gauge 0.5 mm² cable with silicone insulation, 150 mm long, suitable for all rc-systems.Content:1 piece

€12.90*

12 products found for "y0429"

Filter products

rc-car-online - Home