Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Genuine HPI spare/option part. Distances bore to center of servo horn: 26 and 31 mm. Holes tapped with M3 thread.This aluminum steering arm is built extra tough to handle the demands of 1/5th scale vehicles. Use it as a replacement part on the Baja 5T HPI SFL-10MG2 servo, or as an upgrade to the stock plastic servo arm used on the SFL-10 and HPI SFL-MG servos. HPI recommends upgrading to the metal servo gears if upgrading the stock plastic servo arm.Contents:1 piece
Alloy servo arms are a must for strong digital servos, as used in large scale models.This aluminum servo horn fits servos before June 2013 with 5,75 mm 25-spline output shaft.For servos from June 2013 and up with a 8.75 mm 17-spline output shaft please use aluminum servo horn y0750/01, y0750/02.Four different aluminum servo arms are available for the digital power servo No. S5803 and the Smartech servo no. 301502. The slotted aluminum servo horns provide a gentle clamping on the servo's output shaft (using a 2.0 mm Allen wrench).
Genuine GPM spare/option part. Servo saver machined from 6061 T6 aluminum by GPM for Kraton / Outcast 8S. Much stronger than the stock plastic part. The splined section for installation on the servo is machined from 7075 aluminum for increased strength.Fits servos with 25T spline shaft.Comes with a 6061 aluminum adapter frame for installation of a small steering servo (40/20/20 size).Note: due to the replacement of standard servo, the center point of servo is slightly offset, so the length of the servo linkage needs to be adjusted.Contents:1 set
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces
CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece
This high-quality direct mount servo saver is a direct replacement for your kit supplied item.FeaturesStrong composite material for long-lasting durability in all conditions - Servo horn and servo saver combined in one compact unit - 25T servo spline
Item N° y0769 Heavy duty plastic servo arms for Smartech 301502 servo, 3 pcs.Heavy duty plastic servo arm with a total l^enght of 50 mm and six mounting positions.Content:Thee peaces