y6479 HT rear alloy upright
€109.50
Available
Product information "y6479 HT rear alloy upright"
Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.
Comes with adjustment clips and grub screws for the hinge pins included.
Dimensions:
- Bearing seats: 22 x 7 mm
- Hinge pin bore: 6 mm
- Distance wheel shaft/hinge pin: 25 mm
Contents:
- 2 pieces
Nauenweg 55
47805 Krefeld
Germany
Login
Alternatives
Genuine HT spare/option part. Rear alloy uprights for 1:5 and 1:6 models and 4WD Porsche, CNC-cut, optimal fitting, non-twisting even by heat.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 20 mmContents:1 set
Customers also bought
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
Genuine FG spare/option part.Replacement for plastic rear axle mounts FG 6061 and FG 6062.For the installation in 1:6 Off-Road models you need (FG 6920/12) shorter mounting screws.Contents:1 set
Genuine HT spare/option part. Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.Contents:1 piece
Steel ball joint 4 mm thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One each with r/h and l/h thread
Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section
Customers also viewed
Genuine HT spare/option part. Rear alloy uprights for 1:5 and 1:6 models and 4WD Porsche, CNC-cut, optimal fitting, non-twisting even by heat.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 20 mmContents:1 set
Alloy rear uprights, with replaceable hinge pin bushings.Fits FG and Carson/Smartech Attack, Attack Evo, Gas Blaster, Gas Devil, Super Attack, CRT, CRT 4x4, CPT, Uno, Monster Truck, Pick Up, Beetle and C5.The bearing bushings and bearings should be glued in place, as they have minimal play.One each lefthand and righthand version.Please note: for the installation of all popular disc brakes, we recommend: y6479
Item N° 6479/02Rear alloy 08 upright, right, 1 pce.Spare part for FG no. 6479.
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces