y3006 rc-car-online decal sheet yellow

Team decal sheet, suitable for BMW 320si body shells with the order numbers: y1437.Team decal sheet includes the following manufacturers: Deutsche Post, Hankook, Sonax, Castrol, EDGE, Zollner, Sachs, Allgeier, H&R, Exide, GNB. Dimensions:Big decal sheet: 390 x 200 mmPost logo for the roof: 210 x 145 mmM3 rear wing lettering: 250 x 36 mmStripes: 400 x 73 mm

Wheel squares with 3 mm dowel pins. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled.11,5mm wide.Bore diameter 8 mm18 mm square

Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Genuine HT spare/option part. Fully assembled Alloy differential including reinforced differential-tube and "inner-workings", such as original planetary gears, differential bevel gears, bevel differential wheel axles, sealed bearings, differential shafts with needle bearings (high-speed needle bearing).You only have to insert your full-floating axle (halfshafts). Since the FG and Carson are having different internal teeths by the planetary gears, different versions for FG and Carson/Smartech 2WD are available.Even on heavy off-road use and especially on jumps there are often problems with the original plastic differential. Noticeable is also the relatively thin differential-tube of the serial-equipping. Therefore our special offer for the complete Alloy differential including extra reinforced differential-tube.Set includet:8486 Alloy differential housing6068 Bevel differential gear axle6066/01 Differential bevel gear A, spline drive 6067 Differential bevel gear BFG ball bearings, sealed, y19610-rsReinforced differential tube for FG buggy differential, y09028498/01 Needle bearing for alloy differentialContents:1 set

Genuine FG spare/option part. Replacement chassis for FG touring car EcoLine/SportsLine models with short wheel base 465 mm.4 mm alu-chassis. Contents:1 piece