8 products found for "y1472_03"

Catalogue #1

y1452/03 Conversion kit for FG Monster-Modelle to Mega Beetle

Genuine HT spare/option part. Conversion kit for FG Monster-Modelle to Mega Beetle.Das 8, 5 mm Innengewinde der Alu-Verlängerung aus dem Set passt optimal auf die üblichen serienmäßigen Kunststoff-Karosserieträger mit dem Außenmaß von ca. 8 mm. Aufgrund der 22 mm Tiefe des Innengewindes, ist es möglich, die Position der Karosse um ca. 10 bis 15 mm zu variieren!The body mounts are to be installed as shown in the pictures. Content of this set:2 pieces of rear roll cage mount (item no. 305001)2 pieces of aluminum body mount extension (item no. y1452)4 pieces of body clip (item no. 6013)

€34.90*

y1474 Aluminum foil tape, self-adhesive, 50 mm x 45 meters

Genuine HT spare/option part.50 mm wide, self-adhesive aluminum foil tape, especially for heat insulation; i.e. between tuned pipe and plastic or electronic components.Content:1 piece / 45 meters

€9.90*

y1471 Turnbuckle wrench 6 mm

Genuine HT spare/option part. Handy wrench for 6 mm turnbuckles.Maße: Wrench size: 6 mmLength: 75 mmContent:1 piece

€9.90*

y1478 pump for re-fueling and de-fueling

The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece

€19.90*

y1470 Antenna tubes with caps, set of 5

Genuine HT spare/option part. Five antenna tubes with caps.Size: Length: 300 mmContent:1 set

€7.90*

y1477 Losi 5ive-T/2.0/B and Losi MINI 300m steel HD differential drive cups, booted f/r

y1477 Versin: y1477/02 Set for the rear axle+ 20EUR

Genuine HT spare/option part.These heavy duty differential drive cups for front or rear differential in a Losi 5ive-T/B or MINI WRC are made of 300M / Böhler V132 steel and are characterized not only by high hardness, but also simultaneously toughness. The service life is therefore much higher than for the stock cups.300M steel is used in motorsport and aviation for high strength parts. As a highly pure material, it is significantly more expensive than conventional steels, its high basic strength and toughness make the machining a time-consuming task.The shape of these drive cups now allows the use of driveshaft boots and grease lubrication, which increases service life enormously. In addition, these HD drive cups have two sets of slots for the pin of the drive shaft, this means another doubling of the service life.We recommend y0809 Klüber grease for lubrication of closed HD drive cups.A dry run like with stock parts is theoretically possible, but absolutely not recommended because it would waive the enormous advantage of encapsulated lubrication and the associated wear reduction. The set for the rear includes modified stock alloy bearing carriers, which provide improved clearance for the driveshaft boots.You can find advices for installation at the specifications-tab.Contents:Front set:2 pieces of 300M steel HD differential drive cup, front and rear application2 pieces of driveshaft bootsRear set:2 pieces of 300M steel HD differential drive cup, front and rear application1 pair of modified bearing carriers2 pieces of driveshaft boots

Variants from €119.90*

€139.90*

y1473 Extra strong duct tape, 50 mm x 50 meters

Genuine HT spare/option part.50 mm wide, extra strong duct tape, i.e. for repair of cracks in body shells or for preventative taping of RC car body shells.Content:1 piece / 50 meters

€6.90*

y1475 Special front hinge pin brace set for Losi Mini

Genuine HT spare/option part.These hinge pin braces are machined from 7075 aluminum and feature an increased distance between the holes for the hinge pins. They are to be used in place of stock braces LOSB 078F.This allows the use of the front center drive shaft from the 5ive-T LOSB3218 at the wheels. This one is slightly longer than the Mini shaft for the wheels LOS252000, but will be available as spare part in the future. The turnbuckles on steering rods and camber links need some minor readjusting after assembly to restore the correct geometry.At the rear LOSB3218 driveshafts will fit the Mini without modifications. Set with one each front and rear hinge pin brace.Contents:1 set

€24.90*