18 products found for "y1468"
rc-car-online - Home
Genuine HT spare/option part. Once again misplaced nut or bolt or, or ... . The tray for small parts with magnetic vinyl brings this to an end!Dimensions: Length: 105 mmWidth: 85 mmdepth: 10 mmContent:1 Piece
The perfect tool for drilling perfectly round holes without cracks into a body shell.The cap protects the extremely sharp and spiky tip, the convenient handle provides secure grip on the tool.Dimensions:For holes up to 14 mm diameterLength of tip: approx. 45 mmTotal length: approx. 132 mmContent:1 Piece
Genuine HT spare/option part. Die for removing the remains of microencapsulation on the stock Traxxas X-Maxx wheel shafts.After a few tire changes microencapsulation becomes very hard. This will cause the risk of thread seizure and damage. Timely removal of the residues prevents this. A die holder is not required. Turning the die with bare hands will do the job easily.Contents:1 piece
Genuine HT spare/option part.Set includes shock tower Marder y1032, fits Marder, Beetle, Pajero, Monster Beetle Aluminum bulkhead brace for y1031.Contents:1 set
Genuine FG spare/option part. The set includes: 10250/02 FG Body set F2000 1.5 mm 10254 FG Rear spoiler for F1 10455 Frontspoiler 10265/03 y0312 Decals Contents:1 set
The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!
y1438 Thickness:
y1438/03 - 2,00 mm version+ 4.55EUR
Spare part for y1437 BMW M3 Superstar body shell.Available material thicknesses:1.0 mm2.0 mmPainting tips:
Variants from €32.95*
y1418 Color:
y1418/02 - Blu
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow
y1465 Version:
screws only
Genuine HT spare/option part. Hardened special screws for mounting the beadlock rings of MadMax and Losi DBXL rims.For HPI rims due to the screw head diameter only to be used in combination with non-HPI beadlock rings (i.e. MadMax or Losi 5ive-T)!The combination of larger diameter and substantially larger thread depth ensures a secure grip of the screws in the plastic of the rims; the coarse thread also allows for quick assembly.The large head with T10 hexalobular drive distributes the load as wide as possible on the ring.The screws are galvanized for rust protection.Please note: it is not recommended to use the screws in rims which had previously M3 screws installed. With new rims or in exchange for M2.5 screws appropriate strength is ensured.Dimensions: Diameter: 3,1 mmLength: 12 mmHexalobular drive: T10 (Torx) Content:1 Set of 40 screws for one pair of rims.
y1428 Version:
y1428/02 for FG touring cars EVO 2020
Fits FG and Smartech touring cars in combination with HT steel spur gear on-road y1427. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The carrier is available in two versions:y1426/01 Suitable for FG and Smartech touring cars (not for EVO 2020)y1426/02 for FG touring cars EVO 2020
y1467 Version:
y1467/01 Set with Allen head screws 10.9
Genuine Smartech spare/option part.Includes the complete set 26 body mounting washers, 22 support plates and corresponding screws for an original Losi 5ive-T or Losi 5ive-Mini body.Your choice of screws with either Allen head or hexalobular drive (a.k.a. Torx) heads!Content:26 pieces of mounting washers22 pieces of support plates14 pieces of countersunk screws (DIN7991) Allen head M4 x 20, 10.9 grade Alternatively TX10 Torx head, 10.9 grade12 pieces countersunk screws (DIN7991) Allen head M4 x 16, 10.9 gradeAlternatively TX10 Torx head, 10.9 grade
y1466 Version:
y1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt Losi, HPI, CY engines
y0467 Complete gask set for Zenoah 230 + 260, CY, Reely, HPI and Losi 2 bolt engines, setHigh quality gasket set for all G230 and G260 Zenoah engines, all Chung Yang, Reely an HPI Fuely engines from 23 to 30,5 cc. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Set includes gaskets for:cylinder bottomcarburetorisolatorexhaustcrankcasey1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt Losi, CY enginesFull set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket0.5 mm air filter gaskety1016/112 Complete Zenoah G320 sealing setSet includes:y1016/005 Cylinder gasket G320RCy1016/007 Insulator gasket G320RCy1016/013 Crankcase gasket G320RC7332 Silencer gasket7337 Carburetor gasketUnit prices: 20,10 EURy1386/02 SCZ Sealing set for E290 race engineGenuine SCZ spare/option part.Set includes all necessary seals.
%
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orangen beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
%
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square wheel drive, 20 beadlock screws per rim and reinforced beadlock rings. Fits FG, Smartech and many more models.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPER GRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!