y1436 SPEED TEC CRANK Ignition-System (CIS)
Product number:
y1436
EAN:
4058575054573
Product information "y1436 SPEED TEC CRANK Ignition-System (CIS)"
New ignition system for RC Car race engines with air baffles, special 62 mm balanced flywheel, modified ignition coil mount and special Löhin tuning ignition (#1361).
For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.
A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels!
The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course.
This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine!
The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine!
The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling!
As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing.
This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase.
Other benefits of SPEED TEC CIS - ignition system:
The color of the ignition cable and the spark plug cap may vary.
For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.
A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels!
The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course.
This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine!
The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine!
The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling!
As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing.
This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase.
Other benefits of SPEED TEC CIS - ignition system:
- Fits all Zenoah, as well as HPI, Losi-, CY 1/5 & 1/6 engines (incl. Zenoah G320)
- No modifications to the cylinder or the ignition coil mount required!
- No assembly of the flywheel, thus 100% exact fit and running true
- The enclosed Löhin ignition system is designed for speeds up to 25,000 rpm!
- The baffles protect the flywheel from debris (stones, etc.)
- Complete with Löhin ignition and all necessary parts in a nice special bag
- Easy installation: Remove the stock ignition system - install the CIS-ignition - done!
The color of the ignition cable and the spark plug cap may vary.
Login
Customers also viewed
Genuine Speed-Tec spare/option part. Contents:1 piece
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
Genuine Carson spare/option part. 4 bolt version (4 head bolts!)Contents:1 set
%
Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm
The set is delivered with Jägermeister painted. The body is not drilled and fits all 1/5 scale fabricate with a wheelbase of 535 mm.For additional cooling of the motor, there is the option of selecting a cooling air duct in the shopping basket selection.Required body mounts:Mount front: FG 7020/12 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 7012 Body mounts Side body mount rear: FG 7014 Body mounts Measures:Length: 890 mmWidth: 392 mmHeigth: 260 mmWheelbase: 530 mm
%
The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1032HT Aluminum shock tower Marder 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 391,00 EURThe sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!Fits FG Marder, Beetle, Pajero and Monster Beetle.
GRP tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!New structure conceptIn the new line of tyres, the Belt, Insert an Wheel have also been improved to further improve performance in every race situation and at any temperature of use. Vulcanized Beld with new specific weaves angles. Insert with new variable deformation foam material. Wheel made by Dupont (R) plastc material resistant to high temperatures and flexible at low temperatures.Extraordinary GripThe new tyres of this line provide an incredible Durability even on abrasive asphalt tracks, where the previous compounds lasted less.The difference in Duration is very big with an increase of 35%.Incredible DurationThe new tyres of this line provide an incredible Durability even on abrasive asphalt tracks, where the previous compunds lasted less.The difference in Duration is very big with an increase of 35%.Regularity and PerformanceThe new tyres of this line provide Regularity of abolute performance with each subsequent use, compared to competing tyres.The difference is very big because Performance remains 100% even with each subsequent use, and remains 100% until the tyres is finished. Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square driveContent2 pieces / 1 pair