y1410/02 MadMax TARMAC BUSTER one pair rear wheels 80 mm

The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!

Genuine HPI spare/option part. Special 3-piece bead lock wheels for the Baja 5B. A beadlock ring (not included) is bolted onto the wheel to securely hold the tyre in place. No glue is used to mount the tyres, which makes changing the tyres a simple task! Also, the wheels can be used again with new tyres.Made from tough, high-impact nylon for extra toughness, the popular HPI Super Star design is available in a wide variety of colours, with the opportunity to further customize the colour scheme further with a variety of bead lock rings! All wheels and bead lock rings are sold to fit front or rear pairs of tyres.Content:2 pieces / 1 pair

The first 1/5 touring and sports car designed as a 4WD from the ground up. With a wheelbase of 510mm the 4WD chassis is suitable for the FG Mini Cooper and the FG Porsche GT3 RSR bodies. Equipped with a strong 26 cm³ engine, tuning pipe, tank with quick acting closure, 2 differential gears, front disk brake and a lot more. However, the highlight is still the well-known FG 4WD. Maximum traction, easy handling and grip during cornering as well, these are the advantages only a 4WD model can offer.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version of the car includes servos, transmitter, receiver, rechargeable batteries for transmitter / receiver.The 4WD Sportsline chassis opens up a new era within the Touring and Sportscar class of large scale model cars. Main target was the development of a chassis with supreme driving dynamics and ultimate performance. Maximum traction as well as easy handling, sufficient grip in curves, only a fourwheel powered model offers all these advantages. With the new 4WD Sportsline series FG Modellsport once again sets a trend at 1:5 scale.The 4WD Sportsline chassis for the Porsche 911 GT3 RSR is delivered with a wheelbase of 510mm. The fourwheel drive is carried out over an almost wear resistant tooth belt. 2 differential gears, tank with snap closure and a powerful engine with Tuning pipe turn the Sportsline 4WD chassis into a high-class 1:5 scale model with outstanding driving characteristics.You can choose this 4WD model with painted bodyshell , 2.4 GHz radio control system, servos, batteries in our configurator. Team decals are not included in the delivery content and have to be ordered separately.The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problems. A tank filling enables you to run your model around 45 minutes. Equipment and technical description:Solid 4mm chassis made of high-quality aluminium low-wear belt drive splash-proved 2 differential gears double wishbones at front and rear axle toe-in, castor and wheel camber adjustable at the axles - rear FG ball drive all steel driving components hardened all rotating parts ball-beared servo relieving servo saver front disk brake rear gear brake with big brake disk 700ccm fuel tank with snap closure oil-pressure shock absorbers with volume control and spring adjusting ring 26 cm³ combustion engine with Tuning pipe fabric hollow chamber tires with inserts receiver box and battery holder polycarbonate bodyshell 2.4 GHz pistol grip radio control system with steering and gas servo.Dimensions: Length: 980 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURTouring cars in action!Painting tips:

Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The OVER LANDER MadMax are designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the OVER LANDER is the right choice! It can even be used on partially paved tracks! Dimensions:Outer diameter: 170 mmTyre width: 60 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!

Genuine Carson spare/option part. Fits models with a 22 mm hex drive.Contents:1 pairs / 2 pieces

Offerset:1 Pair MadMax Supergrip front tires 170x60 mm1 Pair MadMax Supergrip rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces