12 products found for "y1352"

rc-car-online - Home

y1452 Variable body mount extension, aluminum

Genuine HT spare/option part. Set of two aluminum body mount extensions with two holes for body support and fixation clips.The 8.5 x 1.0 mm female thread perfectly fits the usual stock 8 mm body mounts non-cutting. The thread depth of about 22 mm allows for about 10 - 15 mm of body position adjustment!Content:2 pieces

€14.90*

y1350 Aluminum engine mount for Losi DBXL, reinforced version

Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece

€14.90* €34.90* (57.31% saved)

y1382 Maxi-Pin 1/6 offroad competition tire, 2 pair

The Maxi-Pin competition tire is particularly suitable for tracks with a hard packed surface, as well as for tracks with a higher percentage of carpeting. The tread is not extended into the tire?s sidewall to reduce the side bite of the Maxi-Pin tire; the car remains controllable on such challenging tracks, which makes this tire a must-have for your "tire box"! Since the Maxi-Pin tire has many fine pins for a high number of biting edges and a low tread depth for reduced flex work, depending on the track's surface increased tire wear may be expected.Unit pricesOne pairMaxi-Pin tires39.90 EUR79.80 EUROne pairTire inserts9.90 EUR19.80 EUROne pair32482 Buggy rim14.90 EUR29.80 EUR64.70 / 129.40 EURDimensions:Diameter: 155 mmWidth: 67 mmInner diameter: 106 mm

€79.90*

Configure now

y0352 Offroad tuning spring Dirt-Spring for Losi 5ive-T/2.0 and Mini, set with 24 pcs

Fits Losi 5ive-T, 5ive-B und Mini, Carson Gas Devil/ Hell Devil 4x4. Not for Thunderbolt!.Measures:Socket: approx 33 mmInner diameter: 31,4 mmOuter diameter: 37 mmLength short spring: 103 mmCoils short spring: 8 StückLength long spring: 143 mmCoils long spring: 10 StückFront axle:TypeMeasuresColorItem N°Losi2.3 x 103 mmyellowy0351/01Losi2.4 x 103 mmredy0351/02Losi2.6 x 103 mmbrowny0351/03Losi2.75 x 103 mmbluey0351/04Losi2.8 x 103 mmsilvery0351/05Losi2.9 x 103 mmblacky0351/06Rear axle::TypeMeasuresColorItem N°Losi2.3 x 143 mmyellowy0351/07Losi2.4 x 143 mmredy0351/08Losi2.6 x 143 mmbrowny0351/09Losi2.75 x 143 mmbluey0351/10Losi2.8 x 143 mmsilvery0351/11Losi2.9 x 143 mmblacky0351/12

€129.90*

y1358 PTFE thread sealing tape, 12 mm wide, 10 m roll

Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters

€2.90*

y1322 Molded tire inserts for 190 mm Ø HPI + Losi tires with 60 mm width

Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the red colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 190 mm tire diameter is available in 60 mm.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well.Content:2 pieces/1 pair

€29.90*

y1312 Twin hose bracket

Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €14.90*

Details

y1362 Zenoah carburetor body for WT 603/668/668A

y1362 Version: y1362/02 - for WT 668

Genuine Zenoah carburetor bodies, direct replacement for the used part.Available versions:y1362/01 - for WT 603y1362/02 - for WT 668y1362/03 - for WT 668A

€34.90*

y1351 Tire warmers for 1/5 touring cars

y1351 Version: y1351/03 Complete set+ 149EUR

Genuine HT spare/option part. A must-have for 1/5 on-road racing! Even though it looks funny at first sight for uninitiated people! ;-) Just like in full-size racing our tires need a certain temperature to provide the necessary grip that is needed to achieve good lap times. Usually this means that the car will get really fast times only after a few laps. The driver who uses preheated tires has a considerably advantage. With cold outside temperatures or low grip tracks, like a not so clean parking lot, it often not possible at all to bring the tire temperature up to the required range just by driving. As a result the car will be difficult to control! Measures:maximum outer diameter of 130 mm maximum tire width of 80 mmThat includes all standard 1/5 touring car tires! ( ) Instructions: The tire warmers may be operated only on 12 to 13.8 volts AC or DC. In order to reach optimum operating temperature, a power supply with a 12 - 13.8 volts AC or DC and at least 10 amps output power should be used. The T2m Powerbase y1352 is the perfect solution for this application. The operation of the tire warmers directly from a 12 volt car battery (without Powerbase) is also possible, of course. In order to prevent damaging the filament inside the blanket, they must not be bent and not used without tires!Contents:1 set

Variants from €99.90*

€248.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1353 Battery box for 4 AA cells, choice of versions

y1353 Version: y1353/01 Battery Box with BEC connector

This black plastic battery box accepts 4 AA cells, available with either BEC or universal connector.The universal connector version is also available with receiver switch.UniversalBEC

€4.90*

y1354 SPEED TEC Aluminum insulator for Zenoah and Chung Yang engines

y1354 Version: y1354/02 SPEED TEC Race

Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm

€59.90*

y1354/03 SPEED TEC slanted aluminum insulator for Zenoah G230 - G290

Genuine Speed-Tec spare/option part. SPEED TEC tuning insulator, slanted. Especially for 1/5 & 1/6 offroad cars The slanteded version is required for many offroad cars when installing a taller insulator and for HPI Baja series cars in general. The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning out of the engine at higher temperatures is counteracted! The increased height and optimized port allows for lower fuel consumption!Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets.Please notice: the cylinder shroud y1016/021 must be reworked for angled tuning insulator!Dimensions:Height of aluminum intake 15 until 23 mmHeight of insulator plate: 6 mm Set includes: Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm

€69.90*

12 products found for "y1352"

Filter products

rc-car-online - Home