18 products found for "y1340"

rc-car-online - Home

y1340 Adjustable wing mount with wing for Losi Desert Buggy XL, DBXL-K&N

Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal

€79.90*

y1380 High performance starter rope, carbon grey

3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.

€8.90*

y1360 MD Two-component glue CA-STAR 2K met

Best adhesion properties on many different materials: many metalls like steel / aluminum / stainless steel, many plastics, rubber, porous / absorbent materials.Mixing ratio: 4:1Processing time: approx. 35 minutes Temperature resistance: -20°C to +80°C, short term up to +120°CFeatures:ThixotropicDrip freeExtremely impact resistantMechanical editableGap fill up to 6 mmApplications overhead and in vertical locationsGood chemical resistanceLow bloomingColor: grey

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

y1440 Team Decals Post for BMW M3 ALMS

Team decal sheet, suitable for BMW 320si body shells with the order numbers: y1437.Team decal sheet includes the following manufacturers: Deutsche Post, Hankook, Sonax, Castrol, EDGE, Zollner, Sachs, Allgeier, H&R, Exide, GNB. Dimensions:Big decal sheet: 390 x 200 mmPost logo for the roof: 210 x 145 mmM3 rear wing lettering: 250 x 36 mmStripes: 400 x 73 mm

€34.90*

y1370 SPEED TEC EXPERT Zenoah G320 race ported top end set

Race ported top end set for Zenoah G320 engine.The SPEED TEC EXPERT genuine Zenoah G320 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intakeTransfer port covers:Glued and ready for use Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome groundSet includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portTo achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ().

€289.90*

y1310 Hitec HS-1005SGT/HS-1100WP small mounting set for Losi 5ive-T, 2.0, 5ive-B and Mini

Fits 5ive-T 2.0 as well!Set includes:y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 All steel linkage steering servo/servo saver applicationy1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€139.90*

y1350 Aluminum engine mount for Losi DBXL, reinforced version

Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece

€14.90* €34.90* (57.31% saved)

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

y1390 Sealed ball bearing 15 x 32 x 9 mm

Fits Area 5ive-T clutch bell holder AREA-5T-009. Both sides sealed (2RS) for increased dirt resistance. Does not fit stock parts!Content:Two pieces

€16.90*

y1430 Spark plug tester for 1/5 & 1/6 cars

The spark plug tester wiil be put in line between the spark plug in the engine and the spark plug cap. When the spark plug is in good working order, pulling the recoil starter will produce a spark easily visible in the clear section of the tester (see video!).

€14.90*

y1040 T-connector for hydr. brake system - 1 pce

T-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

y1540 Losi Super Baja Rey / 2.0 / Rock Rey complete set of sealed bearings

Genuine rc-car-online spare/option part. Complete set of sealed (2RS) bearings for Losi Super Baja Rey / Rock Rey.4 pieces 4 x 8 x 3 mm Losi # LOS25700715 pieces 8 x 16 x 5 mm Losi # LOSA6942/016 pieces 10 x 19 x 5 mm Losi # LOS257006Price bought separately 78.56 EURSpecial-offer price for the complete set 39.90 EURContents:25 pieces of of sealed (2RS) bearings

€39.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1330 BMW 320si WTCC 1/5 body shell, painted, 535 wheelbase, white/light blue

Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm

€99.90*

y1340/09 Decal for Desert Buggy XL & K&N DBXL rear wing

y1340_09 Dekorvariante: y1340/09 Dekor zu Desert Buggy XL Heckspoiler

Decal especially for Desert Buggy XL rear wing.Dimensions:250 x 100 mm

€2.90*

y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars

y1345 Size: y1345/01 - 4 x 18 mm

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

€4.90*

13401/13402 Lower front a-arms front for FG Marder, FG Buggy with rose joints a.s.o.

Lower front a-arms for all cars of the Marder family. Made from high quality aluminum, the arms are light weight, stiff and durable. They feature plastic bushings for the hinge pin and come with the required set of rose joint and conical spacer inluded.Contents:1x L/h a-arm with hardware1x R/h a-arm with hardware2x Rose joints4x Conical spacers

€129.90*

y1320 Narrow-Grip 616 type drift tires, mounted and with 24 mm hex for Losi, HPI, MCD

The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.

From €39.90*

Details

y1320 Narrow-Grip 616 type drift tires, mounted and with 24 mm hex for Losi, HPI, MCD

€77.80*

18 products found for "y1340"

Filter products

rc-car-online - Home