21 products found for "y1321"
rc-car-online - Home
Mittelfeste, geschäumte, grüne Reifeneinlage mit profilierten Kanten und eingeformten Senkungen für die Felgenverschraubung.Die mittlere Shorehärte der grünen Reifeneinlage in Topqualität stützt die Reifenschulter optimal und ermöglicht somit ein perfektes Abrollverhalten des jeweiligen Reifens.Die ideale Einlage für einem Reifendurchmesser von 185mm und 70mm breite.Ersatzteil zu MadMax Reifen Maxi Pin.2 Stück, 1 Paar
Genuine HT spare/option part. Vehicle specific decal sheet, suitable for BMW 320si body shells with the order numbers: 8144 and 8144/01.Along with headlights, tail lights, grille and door handles this decal sheet also includes various start numbers, the DEKRA start number masks and a complete set of window masks with BMW-Motorsport logo.Dimensions:Sheet with window masks: 458 x 335 mmLights decal: 247 x 397 mmContents:2 pieces
Genuine Speed Tec spare/option part. Speed TEC Tuning Ignition Löhin RS4 332 new ignition system with offset ignition timing and modified spark breakaway. Advantage of the ignition system: better starting and acceleration due to the modified ignition timing. Higher ignition voltage through modified spark breakaway, resulting in increased charging time for the coil, thereby considerably more torque in the medium rpm range. Suitable for Zenoah and CY engines without modifications. In the picture you can see the original Löhin ignition.Contents:1 piece
Race ported top end set for Zenoah G320 engine. The SPEED TEC CRANK genuine Zenoah G320 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina.SPEED TEC CRANK version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledMachined and polished exhaust and intakeThe case is specially matched with enlarged and polished cross section towards the portsy1016/002+3T Tuning transfer port covers:Reduced cross-section and flow-optimized transfer port cover plates for improved and faster gas flow for the Zenoah G320. The improved gas flow rate improves speed and gives faster throttle response in the medium rpm range. To improve mixture formation, the plates were glass bead blasted after machining. Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome polishedSet includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portTo achieve the optimum performance gain of a SPEED TEC CRANK top end set, we recommend the use of a tuned pipe ().
Fits 5ive-T 2.0 as well!Set includes:y1378 Dymond LiPo special high current receiver battery 14.8V/2200mAhy1306 - Servo voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 - Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 - All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the red colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 190 mm tire diameter is available in 60 mm.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well.Content:2 pieces/1 pair
This two-piece differential cover is easy to attach with the existing screws and provides optimal protection against stones and dirt. Suitable for all 2WD FG Offroad models, not suitable for the 2WD models that are based on 4WD e.g. Fun Cross, Leopard, Truggy and all WB535 models.Also suitable for Carson 2WD models e.g. Uno, Attack, Gas Blaster and more.Contents:1 set
y1321 Version:
y1321/07 Two pairs special tyre inserts 65mm width for MadMax Giant Grip+ 16.9EUR
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the MadMax tires with 170 / 190 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI). Applications:for 60 mm tire width: # y1321/01for 80 mm tire width: # y1321/02for GIANT-GRIP #y1321/06
Variants from €22.90*
federn_dirt_m Version:
y0323/01 - M11, yellow
Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces
y1351 Version:
y1351/01 One pair
Genuine HT spare/option part. A must-have for 1/5 on-road racing! Even though it looks funny at first sight for uninitiated people! ;-) Just like in full-size racing our tires need a certain temperature to provide the necessary grip that is needed to achieve good lap times. Usually this means that the car will get really fast times only after a few laps. The driver who uses preheated tires has a considerably advantage. With cold outside temperatures or low grip tracks, like a not so clean parking lot, it often not possible at all to bring the tire temperature up to the required range just by driving. As a result the car will be difficult to control! Measures:maximum outer diameter of 130 mm maximum tire width of 80 mmThat includes all standard 1/5 touring car tires! ( ) Instructions: The tire warmers may be operated only on 12 to 13.8 volts AC or DC. In order to reach optimum operating temperature, a power supply with a 12 - 13.8 volts AC or DC and at least 10 amps output power should be used. The T2m Powerbase y1352 is the perfect solution for this application. The operation of the tire warmers directly from a 12 volt car battery (without Powerbase) is also possible, of course. In order to prevent damaging the filament inside the blanket, they must not be bent and not used without tires!Contents:1 set
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.
y1421 Versiown:
y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³
Genuine HT spare/option part. The engine quick mount replaces the standard clutch housing. It allows a much faster installation or removal of the engine since the clutch side of the engine is only be clamped by one single screw. The gear plate remains in the vehicle, the motor flange on the engine.The engine quick mount fits all FG 2WD on-road cars with horizontal engine (except Formula 1) Sportsline, Competition and Evo (EVO model range till 2003, except Evo 2020 series).We are sorry, but due to the design the quick mount cannot be used for FG 1/6 off-road and monster cars.For the first time it is now possible to install the Zenoah G320 in these cars! For cars allready equipped with a FG quick mount only the engine flange y1423/02 is required.The quick mount is available in two versions:y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1421/02 for Zenoah G320When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1421/01 does not fit in combination with Zenoah OEM clutch!
Offerset:1 Pair MadMax Tarmac Buster front tires 170x60 mm1 Pair MadMax Tarmac Buster rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01 TARMAC BUSTER 170x80 and 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange headlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars. Due to the extreme load created by the MadMax TARMAC BUSTER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. The TARMAC BUSTER MadMax are designed for use on flat surfaces. Your car will have good traction even on smooth pavement!We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
y1301 Version:
y1301/03 male + female+ 1.8EUR
T-connector male / female with spring loaded 4 mm contact.Select from:y1301/01 - male connectory1301/02 - female connectory1301/03 - one each male and female connector
Variants from €1.80*
y1323 Version:
y1323/02one pair for 80 mm tire width+ 3EUR
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the green colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 170 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well. Applications:for 60 mm tire width: # y1323/01for 80 mm tire width: # y1323/02
Variants from €19.90*
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
Team decal sheet, suitable for BMW 320si body shells with the order numbers: 8144 and 8144/01.Team decal sheet includes the following manufacturers: Hankook, Sonax, Castrol, EDGE, Zollner, Akrapovic, Allgeier, EXIDE, GNB, Sachs, H&R, Samsung. Dimensions:Big decal sheet: 500 x 200 mmM3 rear wing lettering: 250 x 36 mmStripes: 400 x 73 mm
Team decal sheet, suitable for BMW 320si body shells with the order numbers: 8144 and 8144/01.Team decal sheet includes the following manufacturers: EXIDE, Allgeier, Sonax, Hankook, Castro, Edge, H&R, Sachs. Dimensions:Big decal sheet: 510 x 200 mmStripes sheet: 360 x 210 mmM3 rear wing lettering: 250 x 36 mm
Genuine HT spare/option part. Team decal sheet, suitable for BMW 320si body shells with the order numbers: 8144 and 8144/01.Team decal sheet includes the following manufacturers: Deutsche Post, Hankook, Sonax, Castrol, EDGE, Zollner, Sachs, Allgeier, H&R, Exide, GNB. Dimensions:Big decal sheet: 390 x 200 mmPost logo for the roof: 210 x 145 mmM3 rear wing lettering: 250 x 36 mmStripes: 400 x 73 mmContents:1 set
Team decal sheet, suitable for BMW 320si body shells with the order numbers: 8144 and 8144/01.Team decal sheet includes the following manufacturers: Hankook, Sonax, Castrol, EDGE, Zollner, Sonax, Akrapovic, Allgeier, H&R, GNB, Exide, BMW Bank. Dimensions:Big decal sheet: 510 x 200 mmM3 rear wing lettering: 250 x 36 mm