44 products found for "y1304"

rc-car-online - Home

y1324 MadMax tyre inserts green 165x65mm, for Maxi Pin tyres

Mittelfeste, geschäumte, grüne Reifeneinlage mit profilierten Kanten und eingeformten Senkungen für die Felgenverschraubung.Die mittlere Shorehärte der grünen Reifeneinlage in Topqualität stützt die Reifenschulter optimal und ermöglicht somit ein perfektes Abrollverhalten des jeweiligen Reifens.Die ideale Einlage für einem Reifendurchmesser von 185mm und 70mm breite.Ersatzteil zu MadMax Reifen Maxi Pin.2 Stück, 1 Paar

€29.90*

y1104 Maintenance tray for 1/5 cars

Genuine HT spare/option part. Maintenance tray for all 1/5 scale RC car models. The tray with its rubber pad prevents the car from sliding while working on the vehicle at the race or in the basement.Dimensions:Length: 370 mmHeight: 60 mmWidth: 170 mmContents:1 piece

€44.90*

y10304 External fins 0.50 mm, perforated

Replacement part for Power-Lock differential 2014 version with the order number y8605.

€21.50*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

This product is no longer available.

y1303 T-connector charging cable 4mm

Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP

Genuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piece

€39.90*

y1604 SPEED TEC CRANK Team-Edition Zenoah G290 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Piston:Transfer port area optimized for flow and polished, weight reducedand the piston-roof is polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

y1340 Adjustable wing mount with wing for Losi Desert Buggy XL, DBXL-K&N

Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal

€79.90*

y1034 HT Aluminum front suspension for FG Off-Road Buggy 2WD, set

The sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1035HT Aluminum shock tower Off-Road Buggy 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 387,10 EURFits FG Off-Road Buggy 2WD.This front suspension can be used on a FG Monster Beetl 2WD as well, however some new holes must be drilled into the shock tower for this application.

€339.00* €387.10* (12.43% saved)

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

y1204 HT Aluminum front suspension for Carson Comanche, Attack Evo, CRT 2WD + CPT, Smartech MT, Pick-up Truck, Cross Beetle, Monster Beetle

The set includes:Item N°Name:y1206HT Aluminum a-arm front lower l/hy1207HT Aluminum a-arm front lower r/hy1208HT Aluminum a-arm front uppery1209HT Aluminum front bulkhead Ay1210HT Aluminum front bulkhead By1036HT rose joints with conical spacersUnit prices: 249,00 EURPlease note: the hinge pins are not included, you will use the pins from the stock suspension!Suitable for Carson 1/6 (Comanche, Attack Evo, CRT + CPT) and Smartech Monster Truck.Price for the parts bought separately: 253,30 EURIntroductory price: 179,90 EUR / set

€249.00*

y1354 SPEED TEC Aluminum insulator for Zenoah and Chung Yang engines

y1354 Version: y1354/01 SPEED TEC Cross

Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm

€59.90*

This product is no longer available.

y1308 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and Mini

y1308 Version: y1308/03 Set with mount A and Mount B+ 27.9EUR

Genuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 set

Variants from €44.90*

€72.80*

y1301 T-connector male / female spring loaded 4 mm contact

y1301 Version: y1301/03 male + female+ 1.8EUR

T-connector male / female with spring loaded 4 mm contact.Select from:y1301/01 - male connectory1301/02 - female connectory1301/03 - one each male and female connector

Variants from €1.80*

€3.60*

y1303/04 T male to EC5 female

Adapter cable T male to EC5 female.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

y1303/06 TRX female to T-connector

Genuine HT spare/option part.Adapter TRX female (Traxxas batteries) to T-connector.Adapter cable for the LiPo receiver battery in model Traxxas Xmaxx.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

This product is no longer available.

y1303/10 EC5 connector, female

Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

y1303/11 EC8 male connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected plug with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm sockets found on many larger ESCs.Contents:1 piece

€5.90*

y1303/17 XH Balancer extension cable 2S-4S

y1303_17 Version: y1303/17-S3 XH Balancer extension cable+ 0.5EUR

Genuine HT spare/option part.Extension cable for convenient charging of LiPo batteries with XH connector, since the standard balancer connection on the battery is usually uncomfortably short. Available for 2S, 3S and 4S batteries. Silicone insulated cables with a length of approx. 20 cm.Content:1 piece

Variants from €3.40*

€3.90*

y1303/02 EC3 to female T-connector adapter cable

Adapter cable EC3 male to T-connector femaleDimensions:Length cable: 46 mmTotal length: 72 mmContent:1 piece

€9.90*

y1303/18 T-connector male to HXT4 battery side

Genuine HT spare/option part.Adapter cable T-connector male to HXT4 battery side. Dimensions:Cable length: 50 mmTotal length: 97 mmContent:1 piece

€9.90*

y1303/12 EC8 female connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected socket with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm bullet connectors found on many larger brushless motors.Contents:1 piece

€5.90*