16 products found for "y1101"

rc-car-online - Home

y1107 Steel balljoints 5mm/M8, with conical spacers

Genuine HT spare/option part. Two balljoints 5mm/M8 with four conical spacers, to replace FG #6029/1 + balls (Set content like FG 4429/1).Fits almost for all 1/5 and 1/6 scale cars.The maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Contents:2 pieces

€14.90*

y1104 Maintenance tray for 1/5 cars

Genuine HT spare/option part. Maintenance tray for all 1/5 scale RC car models. The tray with its rubber pad prevents the car from sliding while working on the vehicle at the race or in the basement.Dimensions:Length: 370 mmHeight: 60 mmWidth: 170 mmContents:1 piece

€44.90*

y1011 Zenoah G270RC with Walbro carburetor WT 990

26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerNew carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€284.90*

y1501 Balancer adapter board 2S 6S

Genuine HT spare/option part.The adapter board is used for charging of 2S 6S batteries with XH, TP or HP connector on most current chargers with XH connector.Contents:1 piece

€6.90*

y1101 Servo horn mounting screws, 10 pcs

y1101 Application: y1101/05 Ace DS1015 Super Torque Digital Servo

Item N° y1101 Servo horn mounting screws, 10 pcsReplacement screws for mounting the servo horn on the servo shaft.Part is delivered in silver or black color from vendor!Choises:y1101/01Fit:Multiplex Jumbo and Power MCFG 6598 Savöx-Servo SC-0251MGFG 6599 Savöx-Servo SC-1256TG Measures: M3 x 8 mmy1101/02Fit:Multiplex RhinoHitec 805 MGHitec 9805 MGFutaba S3152 Measures: M2,5 x 10 mm Torxy1101/03Fit:Futaba und Robbe diverse ServosPlease check the required dimensions! Measures: M2,5 x 6 mm Torxy1101/04Fit:402115 Mega Power-Servo, metal gears Measures: M3 x 10 mm y1101/05Fit:Ace DS1015 Super Torque Digital Servo, y1051 Measures: M3 x 10 mm

€2.00*

1101 FG Alu Querlenker vorne, oben für FG EVO 04

Original FG ErsatzteilRechts und Links universell einsetzbar.

€29.90*

y1601 SPEED TEC CRANK Team-Edition Zenoah G240 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, the intake is flow-optimized. the case is specially matched with enlarged and flow-optimized cross section towards the ports Cylinder modified for installation of the ignition systemPiston:Transfer port area optimized for flow, weight reduced and the piston-roof is flow-optimized and polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1105 Exhaust port and carburetor intake cover plates, for most usual 23cc - 30cc engines

Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm

€4.90*

y1103 Body support

y1103 Size: y1103/01 - Small

Genuine HT spare/option part. You can select from two different sizes of body support.Dimensions small body support y1103/01:Length: approx. 80 mmWidth: approx. 16 mmDistance bore to bore: approx. 64 mmDimensions large body support y1103/02:Length: approx. 105 mmWidth: approx. 16 mmDistance bore to bore: approx. 88 mmBore diameter: approx. 8 mmContents:2 pieces

€7.90*

y1106/02 Aluminum ball joints with 5mm/M8 left-hand thread, 2 pieces

Genuine HT spare/option part.Two balljoints 5mm/M8 left-hand threadThe maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Dimensions:A = 5 mmB = M8 rightC = 8 mmD = 17,5 mmE = 39 mmContents:2 piece

€14.90*

y1301 T-connector male / female spring loaded 4 mm contact

y1301 Version: y1301/03 male + female+ 1.8EUR

T-connector male / female with spring loaded 4 mm contact.Select from:y1301/01 - male connectory1301/02 - female connectory1301/03 - one each male and female connector

Variants from €1.80*

€3.60*

y1104/01 Foldable maintenance tray for 1/5 and 1/6 cars

Genuine HT spare/option part. Foldable maintenance tray, ideal for 1/5 and 1/6 cars; even for heavy weight and high ground clearence cars like a Losi 5ive-T!Size folded:Width: 300 mmHeight: 315 mmDepth: 40 mmWeight 1 kgSize erected: Width: 300 mmHeight: 220 mmDepth: 210 mmContents:1 piece

€19.90*

7303 Samba 7 Titan Racing tuned pipe system ESW DMC 50-1101

The Samba 7 titanium gives you a weight saving of 140 grams compared to the steel version. We have tested and optimized the Samba 7 Titan- tuned pipe system for half a year on the engine dyno and an additional three months on various racetracks! The pipe has a new, very strong connection system. This low-maintenance flexible connection between pipe and manifold is secured by four (!) springsDespite of the increased performance fuel consumption remains the same compared to a Samba 6 pipe. The Samba 7 system provides significantly better performance, i.e. the power is optimally available across the engines entire rpm range! New New connection from exhaust to manifold Lower center of gravity through new alignment Also suitable for 510 wheelbaseSamba 7 can also be installed in cars equipped with Magura 2 hydraulic brakes (see pictures).Of course, the Samba 7 tuned pipe system is race legal for racing, with the DMC approval number 50-1101 engraved. The Samba 7 - tuned pipe system comes with an installation kit.Fits: All On-road cars from FGContrastBergonzoniHarmGeniusand many others as well<Will fit medium (510 mm) wheelbase cars from FG as wellOriginal statement from Samba: "This new tuned pipe system is the result of the development"

€399.00*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

TT1101 Top Tuning isolator riser and reinforcement plate

Genuine Top Tuning spare/option part.The 4 mm thick FRP isolator plate reduces the heat transfer between cylinder and carburetor. Furthermore, the 4 mm rise through the insulator plate optimizes engine response and reduces fuel consumption.Fits 230 to 290 size cylinders, not for Zenoah G320! Contents:1 piece

€14.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

LOS251101 Losi Radio Tray Set for DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 set

€19.99*

y110010 Cylinder gasket for CY / Zenoah G230/260, different versions to choose from

y110010 Thickness: y11001050 - 0,5 mm

Top quality gasket Available in the following versions: y11001030 - 0,3 mm y11001040 - 0,4 mm y11001050 - 0,5 mm Contents:1 piece

€6.90*

16 products found for "y1101"

Filter products

rc-car-online - Home