15 products found for "y1069"

rc-car-online - Home

y1067 Walbro WT668C carburetor

Genuine Walbro spare/option part.The Walbro WT668C carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The Walbro WT668C features an integrated choke with lever and a throttle shaft linkage lever.The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetor The higher quality alternative is the Walbro WT603B, also with choke. Contents:1 piece

€69.90*

This product is no longer available.

Servosaver Blocker - y1039

Servosaver blocking pin to block the servosaver in a middle position for a accurately setup of the front suspension.Fits on FG EVO Touring Cars 06, 07, 08 and Competition 07.

€11.90*

y1029 HT aluminum droop stops

Genuine HT spare/option part.Required for bulkhead A (y1028).Contents:2 pieces

€32.90*

y1068 HT Aluminum shock tower set 2WD

Genuine HT spare/option part.Set includes shock tower Marder y1032, fits Marder, Beetle, Pajero, Monster Beetle Aluminum bulkhead brace for y1031.Contents:1 set

€69.90*

y1569 Low voltage buzzer with voltage test

Genuine HTspare/option part. The LiPo Voltage Checker provides a low voltage alarm for 28S cell counts.When the voltage is below the set value, an alarm will sound along with illuminating the red LED.The voltage checker will automatically detect the cell count when connected to the balance lead on 28S LiPo. SpecificationsInput: 1S (JST) and 28S (JST-XH) LiPo, Li-ION/LiMN/Li-FeUnit Voltage Display Range: 0.54.5 VTotal Voltage Display Range: 0.536 VTest Mode Voltage Range: 3.730 VAlarm Value Range: 2.73.8 V, including offDimensions: 3.9 cm x 2.4 cm x 0.9 cmContents:1 piece

€9.90*

y1099 Flex wing rc-car-online - 1 pce.

The flexible rear wing for FG and Carson / Smartech offroad cars, with reinforcement ribs on the underside.

€19.90*

y1009 Zenoah G240RC with Walbro carburetor WT 990

23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€274.90*

y1469 Sheet drill with protective cap, up to 14 mm

The perfect tool for drilling perfectly round holes without cracks into a body shell.The cap protects the extremely sharp and spiky tip, the convenient handle provides secure grip on the tool.Dimensions:For holes up to 14 mm diameterLength of tip: approx. 45 mmTotal length: approx. 132 mmContent:1 Piece

€24.90*

y1064 Cable ties, black, 202 x 2.5 mm, 20 pcs.

For the secure installation of driveshaft boots.

€3.90*

y1079 HT Aluminum front bulkhead A + B + droop stops for 2WD

Genuine HT spare/option part. Bulkhead A with provision to mount a stabilizer bar. Bulkheads come with two pairs each of special bushings to adjust camber changes during the suspension movement.Fits 1/6 cars like Marder, Pajero, Beetle and all cars that have FG #6097 installed on the front suspension-Content:y1028 HT Aluminum front bulkhead A for 2WDy1029 HT aluminum droop stopsy1030 HT Aluminum front bulkhead B for 2WD

€79.90*

HT replacement flanged bushing 4 x 5.5, y1096, 4 pcs.

For mounting the brace cam in HT aluminum center diff mounts for Carson / Smartech 4WD cars.Inner diameter 4 mmOuter diameter 5.5 mmWidth 3 mm

€3.90*

Motor for Smartech, Mega Evo, Mega Evo Pro servos, y1169, 1 pce.

€24.90*

VOLZ-Servo, y1060 - 1pce. -Special offer-

Version 220 for steering and throttle/brakeOriginal price: 266,80?Gears: Metal - Steel output shaftBearings: 2x ball bearingWeight: 72gVoltage: 6,0 VoltsTorque: 220 Ncm Speed: 0,11 s. 40ºDeflection: 2 x 45º

€179.90*

y1019 GPM - Ultragrip 170x80/x60 mm complete set for Traxxas X-MAXX 4x4 with adapter

Offerset:1 Pair MadMax Ultragrip front tires 170x60 mm1 Pair MadMax Ultragrip rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01Ultragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced silver headlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring. The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01.We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces

From €129.90*

Details

LOS251069 Losi Roll Cage Top Bar, Front Bar, Super Baja Rey

Genuine Losi spare/option part. Contents:1 set

€19.99*