16 products found for "y0716"

rc-car-online - Home

y0916 Original Zenoah G290 rebuild kit, set

Rebuild kit for the Zenoah G290 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G290Piston G290Piston ring G290Piston pin G290Piston pin retainer clipsCylinder gasketPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer

€94.90*

y0616 rc-car-online Race Cap, 1 pce.

y0616 rc-car-online Race Cap, 1 pce.With rc-car logo on front and back. 100% cotton; with adjustable brass buckle to fit every head size. First class quality and workmanship.

€7.90*

y0116 nitrided hardened Steel pinion with 14 to 48 teeth

Nitrided hardened, highly wear-resistant.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)For use on the clutch bell of FG cars in combination with a 48t spur gear on the layshaft. Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€29.90*

y0726 Gas-nitrided tuning clutch bell for Losi 5ive-T/2.0/B and Mini

Gas-nitrided tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Extreme clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.The bolt hole is countersunk from the inside so you can also use a flat head screw from the inside and a nut on the outside if you like. Content:1 pieces

€49.90*

y0715 rc-car-online High tech mechanics gloves, nitrile, black

Genuine HT spare/option part. With non-slip surface perfect for delicate work, actually improving dexterity and grip.Available sizes: 8, 9 and 10.Glove size?Size 8 = 21 cm (S - L) circumferenceSize 9 = 24 cm (L - XL) circumferenceSize 10 = 27 cm (XL - XXL) circumferenceMeasure the circumference of your hand without the thumb and at the widest point (above the ankle). The tape measure should embrace the hand loosely.Norm EN388, Lining 100% polyamide.Partially coated with hightech nitrile Fits like a second skinGrips even when wetGood touch sensitivityLiquid-repellentGood resistance against oil and greaseContents:1 pair / 2 pieces3 pairs / 6 pieces

€8.90*

y0711 Double sided split alloy servoarm for Savöx SV-0236MG, Rhino and Hitec 805 servo

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:Multiplex RhinoHitec 805Savöx SV-0236MGLOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)and many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€19.90*

y0714 Alloy pinion 19 tooth, hard anodized, for Carson/Smartech 1/6 scale offroad - 1pce.

Item N° y0714 Alloy pinion 19 tooth, hard anodized, for Carson/Smartech 1/6 scale offroad - 1pce.Very low weight hard anodized 19T alloy pinion, for use with the stock 48T spur gear on 1/6 scale 2WD off-road cars from Carson/Smartech/Nutech a.s.o.Diameter 31,6 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€27.90*

y0716/01 Torx screwdriver spare blades

y0716_01 Size: y0716/T6 - T6

Very high quality Torx screwdriver blades with ¼ hexagon shaft and engraved size indication.Sizes T7 to t25 are usually required for rc-cars.Available sizes:T6, T7, T8, T9, T10, T15, T20, T25

€5.90*

y0716/02 Torx screwdriver unit handle module

Genuine rc-car-online spare/option part. Very high quality Torx screwdriver handle module with rc-car-online logo.Contents:1 piece

€9.90*

y0816 Motul Shine&Go

Genuine Motul spare/option part. Motul Shine&Go, a silicone based care for all metal and plastic parts. Protects the surfaces with a long term non-stick protective film, helping to prevent dirt, grime, tire rubber and dust from adhering. Once applied after cleaning the model, dirt can be removed much easier next time.Contents:1 piece

Content: 400 Milliliter (€32.25* / 1000 Milliliter)

€12.90*

y0416 Hobbythek failsafe module

Genuine HT spare/option part.Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!Attention: not compatible with digital servos!Contents:1 piece

€29.90*

y0776 NGK Suppression spark plug cap CY / Zenoah G230/240/260/270/290

The use of NGK spark plug caps with noise suppression resistor offers an optimal suppression of RFI in all frequency ranges without negative effects on engine performance.NGK spark plug caps are equipped with a resistor element made of high quality ceramic material. This ensures a constant resistance value with only a slight deviation in overload conditions. Features: Material: phenolic resinType: 90 degreeColor: Black Resistance: 5 kilo ohms RFI suppression: Yes Waterproof: Yes Cable length: Without cable Connection: SAE terminal nut or integrated terminal Features: Compact type; only 31.5 mm high

€12.90*

y0761 MadMax Extreme 60/80 mm rim black with reinforced color beadlock rings for Losi, Carson Wild GP Attack and HPI cars

y0761 Version: y0761/02 one pair for approx. 80 mm wide tires+ 2EUR

New highly reinforced MadMax rim with 24 mm hex drive and optimized beadlock rings.20-fold screwed very tough and suitable for all 1/6 &1/5 Carson Wild GP Attack, Losi 5ive-T or Desert Buggy XL and HPI cars.The MadMax Extreme rims are available for either 60 or 80 mm tire width.They come with optimized inner and outer beadlock rings, 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench) and reinforcement rings around the wheel hex.Our shop offers you the choice of economically priced sets of the following combinations:y0761/01 one pair for approx. 60 mm wide tiresy0761/02 one pair for approx. 80 mm wide tires y0761/03 two pairs for approx. 60 mm wide tires y0761/04 one pair each for approx. 60 and 80 mm wide tires

Variants from €29.90*

€31.90*

y0711/01 Single-sided split alloy servoarm for Savöx SV-0236MG, Rhino and 805er Servo

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft!Suitable for all servos with an output shaft with 15 tooth spline shaft, for example:Multiplex RhinoHitec 805Savöx SV-0236MGLOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)and many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€18.90*

y0711/03 Split Alloy Servo arm for Losi Super Baja Rey / 2.0 and Rock Rey for 15 tooth spline shaft

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M4 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€14.90*

y2006/01 Double-sided split aluminium servo arm 17 teeth, 1 pc.

Split aluminium servo lever for more gentle screwing (with a 2.0 mm Allen key) with clamping on the servo output shaft! For servos that have an output shaft with a 17 mm multi-tooth shaft. For our y2006 Top Tuning digital Pro Servo 40 Kg Mounting holes with 3 mm diameter If you count the teeth on your servo, you can determine whether this aluminium arm fits your servo. Aluminium servo arms are indispensable for powerful digital servos, such as those used in large-scale models.

€19.90*

16 products found for "y0716"

Filter products

rc-car-online - Home