Genuine Top Tuning spare/option part.Red colored lens for the Losi Super Baja Rey / Rock Rey's rear light bar, gives the LED strip the look of a real tail light. It also protects the LED strip against dirt.The stock mounting screws from the LED strip will be re-used.Contents:1 piece
Genuine Top Tuning spare/option part.Lens for the Losi Super Baja Rey / Rock Rey's front light bar. It protects the LED strip against dirt.The stock mounting screws from the LED strip will be re-used.Contents:1 piece
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting.This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual! FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
Mammoth Supergrip ungluedMammoth Supergrip for 1/6 and 1/5 offroad carsParking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmPlease note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tireRear tireGeneral recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Unitprice FrontRearMammoth SupergripPair44,90 EUR49,90 EURTire insertsPair13,00 EUR13,00 EURFG rimPair14,90 EUR14,90 EURFG extension ringPair--.-- EUR14,90 EURMounting/GluingPair13,00 EUR13,00 EUR Total:82,70 EUR86,90 EUR ================================In combination with rim adaptors no. for all HPI Baja cars as well.
€44.90*
This website uses cookies to ensure the best experience possible. More information...