341 products found for "servo_strom_ohne"

rc-car-online - Home

Servo direct power supply cable, 1 pce.

servo_strom_ohne Application: y0364 - 2 servos, battery connector universal,+ 2EUR

Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section

Variants from €12.90*

€14.90*

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

4495/03 FG Servo-saver A

Genuine FG spare/option part. Content:1 piece

€57.10*

MAKX024 GPM Aluminum servo saver with spring, 25T, with servo adapter frame, Arrma Kraton / Outcast 8S

Genuine GPM spare/option part. Servo saver machined from 6061 T6 aluminum by GPM for Kraton / Outcast 8S. Much stronger than the stock plastic part. The splined section for installation on the servo is machined from 7075 aluminum for increased strength.Fits servos with 25T spline shaft.Comes with a 6061 aluminum adapter frame for installation of a small steering servo (40/20/20 size).Note: due to the replacement of standard servo, the center point of servo is slightly offset, so the length of the servo linkage needs to be adjusted.Contents:1 set

€37.90*

87280 HPI Alloy servo horn for SFL-10 servo

Genuine HPI spare/option part. Distances bore to center of servo horn: 26 and 31 mm. Holes tapped with M3 thread.This aluminum steering arm is built extra tough to handle the demands of 1/5th scale vehicles. Use it as a replacement part on the Baja 5T HPI SFL-10MG2 servo, or as an upgrade to the stock plastic servo arm used on the SFL-10 and HPI SFL-MG servos. HPI recommends upgrading to the metal servo gears if upgrading the stock plastic servo arm.Contents:1 piece

€14.99*

Split alloy servoarm for K-Power, Savöx, Spektrum, Rhino, Hitec and many more Servos with 15 tooth spline shaft

y0711_alle Version: y0711 Double sided split alloy servoarm+ 2.9EUR

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€17.80*

586 Alloy servo arm for Digital Power Servo no. S8203, 1 pce.

smartech_586 Version: 58610 Single-sided

Alloy servo arms are a must for strong digital servos, as used in large scale models.This aluminum servo horn fits servos before June 2013 with 5,75 mm 25-spline output shaft.For servos from June 2013 and up with a 8.75 mm 17-spline output shaft please use aluminum servo horn y0750/01, y0750/02.Four different aluminum servo arms are available for the digital power servo No. S5803 and the Smartech servo no. 301502. The slotted aluminum servo horns provide a gentle clamping on the servo's output shaft (using a 2.0 mm Allen wrench).

€13.90*

6023 FG Servo saver A/B

Genuine FG spare/option part. Suitable for all FG 2WD models.Dimensions:Total height: 26 mmLever for servo linkage: approx. 21 mmLever for steering rod: approx. 40 mmContents:2 pieces

€12.50*

LOS251020 Steering & Throttle Servo Horn S901 Servo Losi DBXL 1/5 4WD

Genuine Losi spare/option part.

€7.99*

LOS231008 Losi Servo Mount, Steering Servo set Plastic, Super Baja Rey

Genuine Losi spare/option part. Contents:1 set

€9.99*

85414 HPI Steering parts / Servo arm set

Genuine HPI spare/option part. Content:1 set

€17.99*

ARAC8883 ARRMA Servo Saver Set 25T

This high-quality direct mount servo saver is a direct replacement for your kit supplied item.FeaturesStrong composite material for long-lasting durability in all conditions - Servo horn and servo saver combined in one compact unit - 25T servo spline

€7.99*