455 products found for "karosse_0017"
rc-car-online - Home
Genuine HT spare/option part. Soft trim for body shell edges and cut-outs. Use speed glue for installation.Contents:1 piece / 3 metersPainting tips:
Content: 300 Zentimeter (€3.30* / 100 Zentimeter)
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURPowerful 26ccm engine with integrated pull-rope starter running with 2 stroke petrol mixturechassis with side protections.Four-wheel independent suspension with numerous adjustment possibilities.Adjustable long stroke Big Bore dampers.Hardened steel transmission on ball bearings.Protection cage can be used as a transport handle.Fully enclosed polycarbonate body, painted and decorated.Nylon rear spoiler with adjustable incidence.Installed and glued spike tires.Dimensions :Length: 770 mmWidth: 465 mmHeight: 300 mmWheelbase: 535 mmWeight: 9,1kg Contents:1 piece
Genuine FG spare/option part. Body shell is delivered white and without decal set.Measures:Length: 530 mmWidth: 300 mmHeight: 190 mmContent:1 piece
Mounting set for Cross-Power tuned pipe for Smartech UNO and Carson Attack
grp_w78_ungeklebt Rubber compund:
Extra Soft - GW78X
Item N° GW78 GRP 1:6 Buggy "CROSS" tire not glued, 2 pcs.Tires will be delivery with inlays and without rims. - Aggressive medium sized x-pattern tread for the Extra soft version and big knobs tread for the S and M version.- Moderate directional stability - Very good lateral traction - Very good propulsion - For loose to medium packed surfacesTires are not glued!
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside.Dimensions:Outer diameter: 170 mmTyre width: 60 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside.Dimensions:Outer diameter: 170 mmTyre width: 80 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. Powerful 26ccm engine with integrated pull-rope starter running with 2 stroke petrol mixturechassis with side protections.Four-wheel independent suspension with numerous adjustment possibilities.Adjustable long stroke Big Bore dampers.Hardened steel transmission on ball bearings.Protection cage can be used as a transport handle.Fully enclosed polycarbonate body, painted and decorated.Nylon rear spoiler with adjustable incidence.Installed and glued spike tires.Dimensions :Length: 770 mmWidth: 465 mmHeight: 300 mmWheelbase: 535 mmWeight: 9,1kg Contents:1 piece
Offerset:1 Pair MadMax Cross Bond front tires 170x60 mm1 Pair MadMax Cross Bond rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01CROSS BOND 170 x 80 mm and 170 x 60 mm tires with black MadMax Extreme 20 bolt-beadlock rims with 24 mm hex drive and reinforced beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. Equipment of the model:Powerful 26 cm³ engineTwo differentials4 mm thick chassisFour wheel independent suspensionsBig Bore dampersDimensions:Length: 700 mmWidth: 460 mmHeight: 310 mmWheelbase: 535 mmWeight: 10,4 kg
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EUREquipment of the model:Powerful 26 cm³ engineTwo differentials4 mm thick chassisFour wheel independent suspensionsBig Bore dampersDimensions:Length: 700 mmWidth: 460 mmHeight: 310 mmWheelbase: 535 mmWeight: 10,4 kg
Genuine FG spare/option part.Suitable for the Formula 1.Contents:1 piece
Genuine FG spare/option part. Measures:Length: 530 mmWidth: 300 mmHeight: 190 mmContent:1 piece
The upgrade kit includes 1 pair of shock absorber aluminium feet and 1 pair of 64mm piston rods. The special feature of this upgrade kit is, as you have probably already recognised from the pictures, that the piston rod is screwed into the foot with a part without thread. This gives the shock absorber considerably more stability. Length of the foot: 26.5 mm Length of the piston rod short: 64 mm Diameter 4.5 mm Thread bottom M4 Top thread: M3 1 set
scs20 Length:
SCS20/02 Shock shafts long, 77 mm
The new version of the shock shafts has a shorter thread so that it can go deeper into the new shock shaft end. This protects the critical transition from the thread to the shaft.Set with 2 shock shafts (long or short version) and 2 shaft ends.Shaft end dimensionsLength: 26.5 mm overall, about 22 mm to center of bushingM4 thread for shock shaft, M3 for pistonBushing i.d. 4 mm Shock shaft length: short 64 mm / long 77 mmThread size for shaft end M4, for piston M3Shaft diameter 4.5 mm