Fits all 2WD Carson / Smartech largescale offroad cars.Will also fit GP buggy chassis "Big Pyro" from Reely.CNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.
y1069 Walbro WT997 carburetor with chokeThe WT997 is certainly one of the most popular carburetors from the big Walbro program because its unproblematic to adjust. For this reason it is especially recommended for the less experienced rc-car driver.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The Walbro WT997 features an integrated choke with lever and a throttle shaft linkage lever.The WT997 is also available with ball-raced throttle shaft under part number # y0036/05 Ball-raced tuning carburetor Walbro WT997 with choke.y0036/05 Ball-raced tuning carburetor Walbro WT997 with chokeWith dual ball bearings on the throttle shaft. Two sealed bearings 2RS type (3/16" x 5/16" x 1/8") shielded by two steel plates (5 x 8 x 0.3 mm). High quality processed and optimized for racing use! The soft stock screw holding the throttle lever has been replaced with a high strength Allen key screw. Since all screws on the carb are imperial sized, so is the key for this screw. A corresponding bit is included in our tool set y0785, or you can use Allen key wrench y0037/03 as well.The WT997 is certainly one of the most popular carburetors from the big Walbro program because its unproblematic to adjust. For this reason it is especially recommended for the less experienced rc-car driver.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The modified Walbro WT997 features an integrated choke with lever and a double ball-raced throttle shaft with linkage lever.The Walbro WT997 carburetor is also available in a standard version under part number # y1069 Walbro WT997carburetor with choke. Fits all Zenoah G230/240/260/270/290/320 engines as well as the respective Chung-Yang (CY) versions, also Losi and HPI Fuelie, Smartech, Carson PT engines, and many others.Normal:Ball-raced:
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!
Item N° y0689/02 FG manuals set Formular 1 Competition 09 German/English, 1 pce.Genuine FG manuals as included with the cars. English or german to choise
€3.90*
This website uses cookies to ensure the best experience possible. More information...