BJ893F GPM front tires 170 x 60 mm for HPI Baja 5B

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre  Please select which tyre you prefer.  You also have the option of having the tyres delivered ready glued for an additional charge.  Please click if you want to have the tyres ready glued! HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs.  - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs.  - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.

HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mm HURRAX extreme tires are available in soft (blue marker!) and medium through our shop menu.Contents:2 pieces tires2 pieces inlays

Genuine GPM spare/option part.Tires for a solid to medium terrain.Diameter x width: 170 x 80 mmContents:2 pieces

Ultragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced silver headlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The complete set includes two each 60 mm and 80 mm tires, or two pairs 60 mm tires for Losi 5ive T in a body covered with wheels (like the original body), with inserts and MadMax EXTREME rims! We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive Set price 2 pairs / 4 pcs. EUR 89,90Regular price EUR 163,40The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

Genuine GPM spare/option part.Tires for a solid to medium terrain.Diameter x width: 170 x 80 mmContents:2 pieces

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Fits all HPI 1/5 scale cars. With BEC connector.

New highly reinforced MadMax rim with 24 mm hex drive and optimized beadlock rings.20-fold screwed very tough and suitable for all 1/6 &1/5 Carson Wild GP Attack, Losi 5ive-T or Desert Buggy XL and HPI cars.The MadMax Extreme rims are available for either 60 or 80 mm tire width.They come with optimized inner and outer beadlock rings, 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench) and reinforcement rings around the wheel hex.Our shop offers you the choice of economically priced sets of the following combinations:y0761/01 one pair for approx. 60 mm wide tiresy0761/02 one pair for approx. 80 mm wide tires y0761/03 two pairs for approx. 60 mm wide tires y0761/04 one pair each for approx. 60 and 80 mm wide tires

Item N° y1183/02FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.For a complete set covering front and rear axle you need part number y1183.This set includes rim adapters with installation hardware for the front axle only.Measures for front:Outer diameter: circa 17,59 mLength: circa 55,10 mm

Genuine FG spare/option part. for FG Evo 2020.2 models.Contents:2 pieces

Genuine HPI spare/option part. Spare part for #15448 Baja 5B High Response Clutch Shoe/Spring Set. When used as standard, the clutch will engage at 8000RPM, which is great for low-grip or muddy surfaces. If used with #15440 Clutch Shoe/Spring Set, the clutch will engage at 7000RPM, ideal for high-grip surfaces.Content:2 piece