T4994 Pirate Desert Short Course Truck 1/7 4WD Brushless RTR

Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

inclusive:Product information "TT56112/520 Top Tuning Monster Brushless Motor 520kV"Genuine Top Tuning spare/option part.SpecificationsMax. amps: 129 AMax. voltage: 57 VMax. power: 7,350 WKV (RPM/Volt): 520 KVMounting hole depth: 8 mmBolt pattern: 4 x M4 at 30 mm pitch circle diameterCase diameter: 57.8 mmCase length: 112 mmFree shaft length: 30 mmShaft diameter: 8 mmWeight: 1260 gConnector: 6.5 mm diameterCable size: 8AWGFeaturesHigh quality bearings4Pole rotor with high quality magnetsStator - super thin silicon steel layersSuper strength 8 mm shaftCNC Aluminium heatsink caseCopper wires with high temperature enduranceContents:1 pieceandProduct information "HW3010420 Hobbywing Ezrun MAX5 HV G2 ESC 250 A, 6-12s LiPo, BEC 8A"The EzRun MAX5 HV G2 is an impressive brushless controller with high-voltage capability. With support for up to 12S LiPo and a maximum output current of 250A, it delivers explosive performance and outstanding linearity. Thanks to intelligent freewheel technology, the speed control remains relaxed and cool even during demanding driving manoeuvres.  This controller is protected against water and dust in accordance with the IP 67 standard. As a result, the MAX5 HV G2 is naturally suitable for use in all weather conditions and can be operated on various surfaces such as mud, sand, ice, snow and water without damaging the power unit. With a powerful integrated BEC, an anti-spark design and multi-directional protection, this controller offers advanced features and high safety. The EzRun MAX5 HV G2 is the ideal choice for RC enthusiasts looking for maximum potential and reliability. By recording and storing real-time data, the operating status can even be monitored. And the upgrade of the sensor cable interface greatly improves the protection and waterproof performance of the controller. With perfect compatibility with Hobbywing's EzRun 56118 SD G2 motor, this power system offers an unbeatable team for optimum performance and protection against overheating.Features - Now with even more power than its predecessor. - Water & dust proof for use in all weather conditions. - Built-in ultra-powerful switching mode BEC to drive a wide range of servos (high power / high voltage servo). - Turbo timing setting included. Especially recommended with the matching motor (e.g. EZRUN 56118SD G2). - Several protective functions: Battery undervoltage protection, controller and motor overheating protection, signal loss protection, current protection. - Supports LED programme card, LCD G2 programme box and the OTA programming module for easier setting of controller parameters. - Data logging function to display various running data in the HW LINK app using the OTA Bluetooth module. - Supports controller firmware upgrade (multifunction LCD-G2 programme box or OTA programming module required for purchase). - Capacitor capacity increased by 45%. - 12 adjustable parameters.technical Data :Type: 1/5 Brushless Sensored Current (continuous/short): 250A / 1600A Input voltage: 6-12S LiPo BEC: 6V/7.4V/8.4V @8A (switch mode) Motor types: Brushless motors (with/without sensor) Motor limits: - 8S Lipo: KV <= 1200 - 12S Lipo: KV <= 800 56118 motor Fan: Yes, operated via the BEC Programming: LED programming card LCD programming box (G2) OTA programming module Separate programming connection Waterproof: Yes Output: 8.00mm Bullet Connector (female) Size: 94.5x59.4x50.9mm Weight: 428.5g Applications: 1/5 buggy, truck Scope of delivery:  Ezrun MAX5 HV G2 ESCBUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance.To finish you need:Engine with clutch and exhaustRemote control with servos and receiver batteryChargerTwo cans of Lexan paintFeatures SummaryUnassembled 1/5th scale electric-powered Off-Road BuggyStreamlined HPI Baja 5B Flux body designAdjustable motor mountAdjustable HD shock absorbersMonocoque chassisLow CG for superior handlingLong travel suspensionViscous torque oil-filled gear differentialAll-terrain tiresBeadlock wheels with metal insert hubsAluminum rear shock towerHard plastic skid platesAdjustable rear wingQuick access to all critical maintenance pointsDual bellcrank steeringCam type servo saverHex socket hardwareGunmetal anodizingFull set of rubber-sealed ball bearingsEnclosed receiver boxChassis SpecificationsOverall Length 817mmHeight: 255mmWidth: Front - 460mm; Rear - 480mmTire Track (to center of tires): Front - 395mm; Rear - 400mmWheelbase: 570mmRide Height: 76mmSuspension Travel: Front - 95mm; Rear - 100mmWeight: 9.6kg (21.3lb)Adjustable Camber: front - shims; rear - screwFront caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock)Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up)Aircraft aluminum 6061 T6 monocoque chassisDouble wishbone suspension with adjustable roll center F/RDrive system: HD metal gears with sealed gear box (8.382:1 gear ratio)Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oilShock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collarWheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub

Carson Drift Attack 2.0 special equipment with 60 mm wide front and rear Narrow-Grip tires!The off-road tire for sandy surfaces and spectacular drifts!With the Carson Wild Attack almost everything for driving (!) is included! The only exception: The fuel mixture from the gas station. (Recommended oil for mixing: y0813/02).The model includes the completely installed 2.4 GHz remote control, incl. transmitter alkalines, as well as a fail-safe system (automatic engine cut-off in case of possible malfunctions!), 20kg throttle servo and 35 kg steering servo, as well as a 2.000 mAh 6V receiver battery with charger and a tool set. Furthermore a spare air filter element and a special mixing canister. A detailed multilingual manual is also included. At the end of the Page you will find an excellent, about 7 minutes duration introduction video to the Carson Wild Attack, which allows even the absolute novice for RC-Carswith combustion engine, the uncomplicated, problem-free entry: Technical details: approx. 70 km/h top speed0 - 70 km/h approx. 2.5 seconds With one tank of gas (700ccm) approx. 40 minutes driving time29cc engine, with pull starterSound reducing tuned pipe exhaust system2-shoe cltch with steel clutch bellA steel differential.Aluminium shocks, dust protectedDrift equipment F+H 60 mm widebead-lock rims with off-road tyresaluminium rim driveradjustable rear wingCompletely ballraced 2WD drivetrain Water protected receiver boxventilated double disc brakealuminium chassisFor driving, only the 2-stroke oil is needed for the fuel mixture.

‘NEW 2025’  FG Short Cross Elektro 4WD model. Pro trucks or short course are becoming increasingly popular in the world of motor racing. They are monstrous, powerful cars with long suspension travel that make spectacular group races possible. The ‘Short Cross’ has reliable mechanics that are fitted with stiffeners and protective flaps. The standard version is only equipped with motor and controller. The 4WD drive ensures problem-free propulsion on any terrain. Our battery recommendation - use 2 3S Li-Po batteries.Technical data:  - Motor 1100 KV, 3600 W up to 6S - 160A ESC/controller  - 4 mm anodised chassis with side protection  - Differential with bevel gears - 4WD drive via belt drive via 2 differentials - Completely mounted on ball bearings  - Big Bore aluminium shock absorbers  - Front and rear double wishbones adjustable in caster/toe-in/camber  - New short course tyres and high-sided rims in M and S hardness. - Matt-black painted and finished body For completion you need :  - Batteries,  - charger  - 1 large steering servo  - Transmitter/receiver setDimensions and weight:  - Length 770 mm  - Width 480 mm  - Height 320 mm  - Wheelbase 485 mm  - Weight approx. 10 kg1 pieces

The Wheelbase of the WB535 2WD version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models. The body is delivered crystal clear. A sticker set with a custom design is available in our shop. The body is also available painted white in our shop selection. Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm