Samba 50012 Moca Carbon rear wing WU

Available at last: the carbon rear wing for the Audi A4 body shell. Can be used for other body shells as well; please do your own measurements befor ordering!The set includes:1 x profiled carbon rear wing2 x brackets, l/h and r/h2 x backing plates to prevet ripping the body shell screwsWith complete l/h and r/h brackets, mounting hardware and backing plates which distribute the load over a larger area to prevent premature ripping of the mounting points.Size and weight:Total weight: 79 gramsOverall width: ca. 268 mmMounting hole bolt pattern: approx. 253 x 32 mmDepth: 60 mmContents:1 piece

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Carbon Rear wing foil section in light and solid construction, variable angle of incidense, high depression. 1-wing version suitable for all 1:5 touring car models.

Genuine Samba spare/option part. Our Carbon Rear Wing design in the "spoon" style.We use our special rear wing mounting structure also for this wing which makes the stability and the fixing of the wing easy.Very strong structure.Weight: 58 gramContents:1 piece

Original FG spare/tuning part.  Carbon side protection protects chassis and body.  Length 188mm  width 20mm  Bore 8mm  Content 2 pieces

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Crankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Genuine Samba spare/option part. The body shell is neither cut nor drilled, clear and can therefore be adopted to all touring cars with a 530/535 mm wheelbase.We have decided to make a new TC bodyshell to offer a new car from the WTTC series for the 5th scale drivers.Currently the most sought after large scale body shell with optimal aerodynamicsMaterial thickness 1 mm. The body shell consists of one part.Precut, the final cutting must be made according to the chassis you use it on.Width front / rear: 392 mm.Contents:1 piece