LOS351017 Losi Servo Saver Top, Aluminum, Black, DBXL-E 2.0

€29.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los351017

EAN: 605482493427

Product information "LOS351017 Losi Servo Saver Top, Aluminum, Black, DBXL-E 2.0"

Genuine Losi spare/option part.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

y1408/01 MadMax OVER LANDER 170x80/x60 tires for HPI + Losi (24 mm hex drive)

OVER LANDER 170 x 80 mm and 170 x 60 mm tires with reinforced beadlock rings on black rims. The OVER LANDER were designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the Overlander is the right choice! It can even be used on partially paved tracks!Of course, the OVER LANDER allround tire will not make special purpose tires like the TARMAC BUSTER,BIG DIGGER or CROSS BOND obsolete. Due to the extreme load created by the MadMax OVER LANDER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

€119.90*

Configure now

AT-DBXL009/010 ATOP Front and rear shock tower for Losi Desert XL/XL-E +MTXL

Genuine Atop spare/option part. CNC-machined 6061-T6 aluminum shock towers for Losi DBXL. Direct replacement for the stock part.Contents:2 piece

€119.90*

AT-DBXL025 ATOP aluminum front top chassis brace for Losi DBXL-E 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front top chassis brace; fits Losi DBXL-E 2.0 only.Stiffer than the stock plastic part (from set # LOS251097), the aluminum brace reduces chassis tweak in the area of the steering assy. Contents:1 piece

€34.90*

DBXL018/019 ATOP Aluminum rear chassis brace 1+2 for DBXL-E 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum rear chassis brace 1 + 2 for Losi DBXL-E 2.0.Compared to the stock plastic part (from set # LOS251100) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 set

€69.90*

DBXL017 ATOP Aluminum front chassis brace for DBXL-E 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front chassis brace for Losi DBXL-E 2.0.Compared to the stock plastic part (from set # LOS251100) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 piece

€29.90*

Similar products

LOS254006/01 Suspension Arm Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Content:1 piece

€16.90*

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*