Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

LOS351014 Losi Dual Servo Steering Links DBXL-E 2.0

Product information "LOS351014 Losi Dual Servo Steering Links DBXL-E 2.0"

Genuine Losi spare/option part.

Contents:
  • 1 set

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

LOS252067 Losi Diff Rebuild Kit, Al Diff Housing, DBXL-E
Genuine Losi spare/option part. Contents:1 set

€29.99*

Average rating of 0 out of 5 stars

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0
Genuine Losi spare/option part. Contents:10 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS254010 Losi Hinge Pin, Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€19.99*

Average rating of 0 out of 5 stars

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

Average rating of 0 out of 5 stars

LOS254006 Losi Suspension Arm Set Losi DBXL/DBXL-E/DBXL 2.0 1/5 4WD
Genuine Losi spare/option part. Content:4 pieces

€59.99*

Average rating of 0 out of 5 stars

LOS254009 Losi Hinge Pin Brace Inserts, Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€9.99*

Average rating of 0 out of 5 stars

LOS352009 Losi Wheel Nut, Captured, Black, DBXL-E 2.0
Genuine Losi spare/option part. Contents:4 pieces

€39.99*

Average rating of 0 out of 5 stars

LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€39.99*

Average rating of 0 out of 5 stars

LOS252126 Drive Pin Rebuild Set DBXL-E 2.0

€9.99*

Average rating of 0 out of 5 stars

LOS253028 Losi Shock Rebuild Kit, DBXL-E 2.0
Genuine Losi spare/option part. Contents:1 set

€19.99*

Average rating of 0 out of 5 stars

LOS252065 Losi Pinion Gear, 14T, 1.5M, 8 mm Shaft
Genuine Losi spare/option part. Contents:1 piece

€19.99*

Average rating of 0 out of 5 stars

LOS252061 Losi Center Diff Spur Gear, 48T, DBXL-E
Genuine Losi spare/option part. Contents:1 piece

€49.99*

Customers also viewed

Average rating of 0 out of 5 stars

y1309 All steel linkage for steering servo/servo saver application
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency