LOS254065 Losi Front & Rear Sway Bar Set for DBXL-E 2.0
Product number:
losi_los254065
EAN:
4058575124054
Product information "LOS254065 Losi Front & Rear Sway Bar Set for DBXL-E 2.0"
Genuine Losi spare/option part.
Contents:
Contents:
- 1 set
Login
Customers also bought
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!
Genuine Losi spare/option part. Contents:1 set
Genuine Losi spare/option part. Contents:2 pieces
Genuine Losi spare/option part. Contents:1 piece
Similar products
Genuine Losi spare/option part. The esc mounting bracket is equipped with an extremely strong double-sided adhesive tape for fixing the controller. Additionally the esc can be secured with the Top Tuning Velcro TT1021/12, which you can select from the shopping options.Compared to the standard plate, the support surface has been widened by 1mm, so that the ZTW 300A controller can be mounted ideally; slipping back and forth is securely avoided.Contents:1 set
Genuine Losi spare/option part. Contents:10 pieces
Genuine Losi spare/option part. Contents:1 set
Genuine Losi spare/option part. Contents:6 pieces
Genuine Losi spare/option part. Contents:1 piece
Genuine Losi spare/option part. Contents:1 set
Genuine Losi spare/option part. Contents:2 pieces
Genuine Losi spare/option part. Contents:1 piece
Genuine Losi spare/option part. Contents:1 set
Customers also viewed
Walbro Vergaser WT1107 with choke Standard carburetor for Zenoah G320. Typ: Walbro WT1107This is the stock carburetor used for the G320RC engine, and will also work on all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³. Dimensions:Bore: 15,88 mmVenturi: 13,5 mmIndependent tunable high and low speed jets.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³.
The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 510 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.Dimensions: Length: 780 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm Touring cars in action!Painting tips:
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!
%
Only fuel from the gas station and off you go 100% RTR Incl. y0813/02 Motul 800 Racing Oil Off-Roadd One tank of gas 30 minutes Driving fun! Sufficient for the first 20 hours of driving 200 cm³ of oil per 5 liters of gas Including tuning parts worth over 100 euros The DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools
Beast Edition: Standard equipment: Beast Edition: Motor: 780kV 520kV Regler: 160 Ampere 300 Ampere S-Leistung: 8S 12S The original DBXL-E set the world on fire as the go-to vehicle for large scale bashers and enthusiasts alike. Its agile handling, out of the box speeds and durability make it a fan favorite. Now the Losi® DBXL-E 2.0 continues to build on the legendary status! Known worldwide for their dominance in the gas 1/5 market, especially with the 5IVE-T 2.0, Losi has built the DBXL-E 2.0 to be cleaner and easier to use, but with performance and speed that outruns the competition. At home in any environment from dirt to pavement, wet or dry, especially with its 4WD drivetrain with larger 5mm drive pins, the desert buggy makes sure all the power is put to the ground. Drivers stay in control with a DX3 transmitter, a Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver, and scale-to-size Maxxis Creepy Crawler LT tires. This desert buggy features all the technological advances drivers. Finally, the DBXL-E 2.0 has a Losi race-inspired motorsports themed livery for that true off-road look. You get all this and more from the brand that represents the pinnacle of performance.The Full-Throttle Freedom of AVC® TechnologyThe receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditionFeatures ZTW BEAST Pro 300A 12S ESC Top Tuning BEAST Brushless Motor 520 kV Spektrum DX3 radio system with AVC® and new SR6100AT Receiver Spektrum S906 1/5th scale metal gear servo Water protected components Aluminum Shock Towers Aluminum Center Diff Cup New Radio Tray designed for use with single or dual steering servos. New Heavy Duty Drivetrain with 5mm drive pins New Electric Chassis specific chassis braces for increased durability and strength Spedial motor adapter plate Modified ESC mounting bracket Beast decal sheet New ESC Mount Pinned Center Outdrive Cups New Gearboxes for improved drivetrain strength and stability New Steering Rack with helical servo saver design Updated Front and Rear Bulkheads Maxxis Creepy Crawler LT Tires Losi and Fox Shox race-inspired Motorsports themed livery Laser Etched FOX Logo Shock Caps Roof-mounted LED bar Dimensions Height: 317 mm Length: 844 mm Width: 495 mm Weight: 9,8 kg