Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

LOS252008/02 13T Pinion Set Losi DBXL+MTXL 1/5 4WD

Product information "LOS252008/02 13T Pinion Set Losi DBXL+MTXL 1/5 4WD"

Genuine Losi spare/option part.

Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

LOS252017 Axle Boot Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:10 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252009 Differential Rebuild Kit Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€8.99*

Average rating of 0 out of 5 stars

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

Average rating of 0 out of 5 stars

LOS252006 Front/Rear Differential Outdrive Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:2 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252135 Losi Center Driveshaft, rear: DBXL 2.0
Genuine Losi spare/option part. Contents:1 piece

€39.99*

Average rating of 0 out of 5 stars

LOS252016 20T Pinion Gear Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 piece

€19.99*

Average rating of 0 out of 5 stars

LOS252134 Losi Center Driveshaft, Front: DBXL 2.0
Genuine Losi spare/option part. Contents:1 piece

€39.99*

Average rating of 0 out of 5 stars

LOS252008 FR/R 43T Ring and 13T Pinion Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€69.99*

Average rating of 0 out of 5 stars

LOS251024 Brake Pads/Springs/Cam/Discs Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€49.99*

Average rating of 0 out of 5 stars

LOS252002 Center Dog Bone, short Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. 

€39.99*

Average rating of 0 out of 5 stars

LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:2 pieces

€39.99*

Average rating of 0 out of 5 stars

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*

Customers also viewed

Average rating of 0 out of 5 stars

7319/09 FG Easy cooling fan for CY / Zenoah / Fuelie / Losi engines
Genuine FG spare/option part. For Zenoah G230/240/260/270/290/320 enginesSpare part for :Zenoah G230, G240, G260, G270, G290, G320 enginesContents:1 piece

€89.00*

Average rating of 0 out of 5 stars

ST-AN42 SPEED TEC 0,25/0.50 mm, AN - expansion sealing gasket for Zenoah and 4-Bolt Chung Yang engines
st_an42 Thickness: ST-AN42/050 - 0,50 mm
Genuine Speed-Tec spare/option part. For Zenoah G240/G270/G290 and 4-Bolt Chung Yang enginesAN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece

€4.40*

Average rating of 0 out of 5 stars

LOS55000 Tuned Exhaust Pipe, 23-30 cm³ Gas Engines for DBXL/2.0/MTXL
The most popular option part for a 1/5-scale gasoline-powered RC vehicle is a tuned pipe. For the Desert Buggy / Monster Truck XL, this is no different. We have been working with one of the most experienced aftermarket tuned pipe designers and we have a very effective solution. This tuned pipe was specifically designed for the Desert Buggy / Monster Truck XL to provide a 1-2 horsepower increase in performance and to give the Desert Buggy / Monster Truck XL the sound it deserves.DBXL 2.0 Tech Notes:For compatibility with the DBXL 2.0 model (LOS05008T1/T2), you must install DYNR0112 Aluminum Throttle Servo Arm.FeaturesSimple bolt-on installationInstant horsepower and performance increaseSounds amazing!Included all mounting hardware and fixtures

€229.99*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency