FG Monster Truck 2WD with yellow body, RTR, used.

Highlights News 2026 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos, 2 servo for throttle brake, batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

Genuine HT spare/option part. Extra wide tire mounted and glued on genuine 1/6 scale FG Stadium Truck rims 6232/01.Diameter 165 mm, width 90 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.Available in three different compounds:SoftHardWe have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels, which is a labor intensive job. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.However, the original FG-rim lasts without problems!Unit prices:Mammoth tires extra wide: 47,20 EUR / pairMammoth inserts extra wide: 9,70 EUR/ pairGenuine FG wide track rims 6232/01: 29,90 EUR / pairMounting + glueing rims / inserts / tires: 13,00 EURTotal: 99,80 EUR Contents:2 piecesAlso suitable for:With the following wheel adapter: y1183 Rim adapter

The 2WD-465 Sportsline electric model is based on a short chassis (465 mm wheelbase) with double wishbones Rear and front axles built. The vehicle is factory equipped with the 2-damper front axle.E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Sportsline models are equipped with a powerful brushless engine and a Brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.In the unpainted version Version does not include a decal sheet!Features:The front axle of the GT2 was widened to 384 mm. The rear axle is 395 mm wide.Chassis short 465 with double wishbones on the rear and front axle completely assembled, ball bearings, differential gear, oil pressure shock absorber, multi-part unpainted polycarbonate body (item no. 05160L), white spoke rims, tires and tire inserts.T2M standard equipment brushless motor and ESC, 6S - 150A controller up to 3-6S  - brushless motor 6S You can order a motor/ESC combination with 8S for an additional charge.- ESC 200A, 3-8S LiPo, BEC 8A - Brushless Motor 8S The model is also available in our shop selection including complete RTR equipment! RTR features RTR = Ready to Run. The RTR version is delivered ready to drive and with the 2.4 GHz remote control installed.Decor set: selectable (included in the painted version)LiPo batteries and the appropriate charger are required for all versions of the electric models. We recommend using LiPo batteries with a maximum length of 150mm and a width of 50mm to ensure trouble-free installation. The model is supplied with an EC8 connector system.

FG Short Cross 4WD with a 26cc engine and painted black body.RTR available.Pro trucks and short course vehicles are becoming increasingly popular in the world of car racing. They are monstrous, powerful cars with long suspension travel that enable spectacular group races. The “Short Cross” has reliable mechanics that are equipped with stiffeners and protective flaps. A highly detailed polycarbonate body fits the chassis perfectly. The 4WD drive ensures smooth propulsion on any terrain. You can select the car with complete RTR-equipment from the options menu.RTR-equipmentRTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed.Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-batteryFor an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG. The standard price for the individual parts is €200.30. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt.4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURVehicle features:  - Angled 4 mm aluminum chassis  - 26cc 2-stroke gasoline engine  - Completely enclosed belt drive  - Two differential gears on the front and rear axles with hardened bevel gears  - Enclosed front axle housing  - Front and rear bumpers  - Double wishbones on front and rear axles  - Gearbox brake  - Adjustable right/left threaded rods on the tie rods and on the front and rear wishbones  - Steering knuckles with steering stops at the front  - Gears made of case-hardened steel, completely ball-bearing mounted  - Four large-volume oil pressure shock absorbers  - Receiver box The model is equipped with a powerful 26ccm combustion engine with silencer and ready-to-use oiled air filter. It requires a normal 2-stroke gasoline-oil mixture (available at any gas station). The tank capacity of 0.7 liters allows for a driving time of about 45 minutes. Thanks to the built-in pull starter, the engine can be started easily without external starting aid. The RTR version comes with a mounted and adjusted remote control system and rechargeable batteries. All standard servos and remote controls are suitable for completing the non-RTR models. Dimensions and weight:  - Length 770 mm  - Width 480 mm  - Height 320 mm  - Wheelbase 485 mm  - Weight approx. 12 kg  1 piece