Please choose between 10, 15 or 20 viscosity. 100ml content, 1 pieceShock absorber oil, especially for HPI Baja 5B RTR and Mecatech Klick-Shocks, 100 ml bottle.HPI does not recommend silicone oil in their RTR shocks.Viscosity of silicone oil at various temperatures.
Weight-optimized, extremely solid rear spoiler with double wing made of impact-resistant polyamid. The spoiler generates enormous downforce on the rear axle. Suitable for the models 1:6 Off-Road Buggy, Leopard , Marder, 2WD, 4WD and models of other manufacturers.Measures:Length 115 mmWidth 280 mmHeight 40 mm
Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal
Original spare part for Smartech Uno.1:6 rear wing in white with original Smartech Uno decor.Thickness: approximately 3 mm.Suitable for most 1/6 FG, Smartech, Carson, etc. models.
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price 85,80 EUR 105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter
Genuine Smartech spare/option part.Please note: Color and design of Smartech springs and shock bodies may vary from batch to batch.Dimensions:Mounting hole distance: 127 mmTravel: 30 mmDiameter: 16 mmContent:2 pieces
Diameter: 123 mmWidth: 65 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Rims with 18 mm square drive (fits FG, Harm, RS5, Carson, Smartech a.s.o.).Contents:1 pair (2 pieces)
Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) Tuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre
Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).