Genuine FG spare/option part. Washers for the screws (M4 / M5) that hold the engine mounts to the chassis. Suitable for all FG models.Dimensions:Outside diameter: 15 mmInside diameter: 6 mmContents:4 pieces
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
Adhesive and Seal RemoverSeal and Bond Remover is a slow evaporating universal degreaser that is also perfect for quickly and efficiently removing all types of adhesive and sealant residue. The product softens most adhesives and sealants to make them easier to remove.Seal and Bond Remover is suitable for all types of metals and most plastics. In addition, it can be used without risk on almost all modern paints. This makes it particularly suitable for removing stickers, emblems, bumper trims and any adhesive residue that may remain. Even traces of sealant and adhesive after dismantling brackets, etc. can be safely removed without damaging the substrate. Seal and Bond Remover is also ideal for making surfaces free of grease and silicone, for example before applying new stickers, emblems, etc.Due to its high dissolving power, Seal and Bond Remover is also a recommended solution for removing tar splashes or even rubber from trim, etc.In the spray can, Seal and Bond Remover is particularly user-friendly and practical to use. Thanks to the unbreakable nozzle with spray tube, even hard-to-reach places are easy to reach. In addition, the spray can has a special valve that allows it to be used in any position. This allows emblems and bumper strips, among other things, to be removed most effectively by spraying Seal and Bond Remover directly behind the part in question while slowly pulling it off. HIGHLIGHTS. Very easy to use. Ideal for removing adhesive, tar, sealant and chewing gum residues Significantly facilitates the cutting out of glued car windows. Does not attack paint or most plastics in any way OEM approved CONTENT Base: Mixture of aliphatic and aromatic hydrocarbons. Density: 762 kg/m³ Consistency: liquid (ready to spray in aerosol can) Viscosity: ± 2 mPa.s Solvent: mixture of aliphatic and aromatic hydrocarbons. Flash point: 0°C Evaporation residue: None, the product dries without residue. Processing conditions: +10°C to +40°C Substrate: The most common substrates. If necessary, test in an inconspicuous place. USAGE.Shake spray can well before use. Spray Seal and Bond Remover on the surface to be treated and allow to act briefly. Remove adhesive, tar, sealant, chewing gum residues with a Multi Wipe. Wipe off with a clean, dry cloth or Multi Wipe. For thicker layers, remove the top layer first and then repeat the treatment. Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F Details: OEM approval
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).