85434 HPI Rear Buldhead

€24.90*

Prices incl. VAT plus shipping costs

Currently unavailable

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Product number: hpi.h85434

EAN: 4944258854342

Product information "85434 HPI Rear Buldhead"

Genuine HPI spare/option part.

Content:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

104965 HPI Super Heavy Duty Diff Shafts 25 x 48 mm

Genuine HPI spare/option part. Seriously beef up your Baja drivetrain with the Super Heavy Duty Diff Shaft! This is standard equipment on the Baja 5SC but will easily fit the Baja 5B, Baja 5B 2.0, Baja 5B SS and Baja 5T to dramatically increase the longevity and strength of your buggy or truck's drivetrain.Content:2 pieces

€36.00*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Details

y0702 Copper-Exhaust gasket for Zenoah, CY, Fuelie, PT, etc.

Genuine HT spare/option part. For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PTTemperature and dimensionally stable. Thickness: 1,0 mm.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€2.45* €4.90* (50% saved)

y1478 pump for re-fueling and de-fueling

The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece

€19.90*

Details

y1419/02 Sintered steel clutch complete set for Losi 5ive-T/2.0, Mini and Desert Buggy

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch

€49.90*

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi

Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€24.90*