8412/01 FG Carrier disk for adjustable clutch Zenoah

Spare part for .

Spare part for .

Offerset:1 Pair MadMax Over Lander front tires 170x60 mm1 Pair MadMax Over Lander rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01OVER LANDER 170 x 80 mm and 170 x 60 mm tires with reinforced beadlock rings on black rims. Were designed the OVER LANDER as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the Overlander is the right choice! It can even be used on partially paved tracks!Of course, the OVER LANDER allround tire will not make special purpose tires like the TARMAC BUSTER,BIG DIGGER or CROSS BOND obsolete. Due to the extreme load created by the MadMax OVER LANDER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces

Genuine FG spare/option part. Spare part for 4493.Contents:1 piece

Genuine FG spare/option part. The following items are required for completion: body mounts, body, LiPo driving batteries and charger.This model is based on the Sportsline 4WD chassis modified for drift driving.It features an aluminium engine mount and crown gear, short gear ratio, universal drive shafts, harder suspension, special slick tires.Dimensions : Length : 830mm Width : 405 mm Height : 260 mm Wheelbase : 510 mm Weight : 10,2 kgRTR version : RC System 2.4GHz Steering servo 26 kg Brushless engine 1300KV 150A controller