8147 FG Rear wing BMW 320si WTCC, Samba MOCA and BMW M3 Superstars

Genuine FG spare/option part.Body detail kit with different rearview mirrors, windscreen wipers and aerials to give the Touring car bodys a more detailed look.Contents:1 set

Item N° 8140 Alloy plate for front axle - 1pce.Alloy plate for front axle on touring cars.

Also available in .

Genuine FG spare/option part. Detailed BBS wheels in colour white. Rim with 18 mm square driveDimensions:Narrow version in 65mm widthDiameter of the wheels: 95mmContent:2 pieces

The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The body shell is vac-formed from 2 mm Lexan.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase. The set is delivered as shown.Required body mounts:Mount front: FG 7020/12 Front bumperRear body mount: FG 7152/01 Rear body mount Side body mount front: FG 7014 Body mountsSide body mount rear: FG 7014 Body mountsMeasures:Length: 890 mmWidth: 392 mmHeigth: 260 mmWheelbase: 530 mm

Genuine FG spare/option part. Contents:1 set

Genuine FG spare/option part. Up to version 2004.Contents:1 piece

Genuine FG spare/option part. Fits on 2WD and 4WD touring car chassis' with 535 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan.Clear for 1/5 scale for 530/535 mm wheelbase. With rear wing.Required body mounts:Mount front: FG 7020/15 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8014 Body mounts Side body mount rear: FG 9014/01 Body mounts Contents:1 piece

Genuine FG spare/option part. Contains only the front body. If you need a complete body we advise 8180.The front body is delivered not painted.Contents:1 piecePainting tips:

Suitable for Mono axle.

Genuine FG spare/option part. Contents:1 piece

Genuine HT spare/option part. Contents:1 set

Genuine HT spare/option part. Perfect surface preparation for paint jobs.Metal-free grinding fleece with a 1000, 1200 or a 1500 grit to roughen the inside of the body shell to improve paint adhesion. The flexible carrier of the fleece allows for a consistent, uniform contact with the work surface and makes it possible to prepare the polycarbonate to the smallest corner.Use it dry or wet when you rinse the body shell. The 1,500 grit (y0544//03) is especially recommended for metallic paint.Contents:5 pieces PadsPainting tips:

Available at last: the carbon rear wing for the Audi A4 body shell. Can be used for other body shells as well; please do your own measurements befor ordering!The set includes:1 x profiled carbon rear wing2 x brackets, l/h and r/h2 x backing plates to prevet ripping the body shell screwsWith complete l/h and r/h brackets, mounting hardware and backing plates which distribute the load over a larger area to prevent premature ripping of the mounting points.Size and weight:Total weight: 79 gramsOverall width: ca. 268 mmMounting hole bolt pattern: approx. 253 x 32 mmDepth: 60 mmContents:1 piece

Highly flexible driveshaft boots, equivalent to HPI part # H86479.Available in the following colors:y86479/01 - blacky86479/02 - redy86479/03 - orangeContents:4 pieces

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 530 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 890 mmWidth: 392 mmHeight: 240 mmWheelbase: 530 mm

Genuine FG spare/option part. The body set contents the main part, front body and the rear wing. The body is clear.Required body mounts:Mount front: FG 7020/06 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mmContents:1 piecePainting tips: