Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6825/07 FG Screw tap M7 left-hand cutting

Product information "6825/07 FG Screw tap M7 left-hand cutting"

Genuine FG spare/option part.

Screw tap to cut new thread borings and to recut defective ones.

Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

%

Average rating of 0 out of 5 stars

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€15.45* €16.45* (6.08% saved)

Average rating of 0 out of 5 stars

y1004/01 Driveshaft boots for ball drive and dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt.For FG and Carson ball drives, fits standard dogbones as well.Content10 pieces

€34.90*

Average rating of 0 out of 5 stars

6824/07 FG Screw tap M7
Original FG Ersatz-/Tuningteil.Screw tap to cut new thread borings and to recut defective ones.Inhalt:1 Stück

€25.84*

Average rating of 0 out of 5 stars

6077/08 FG Spacer bushing for rear upright
Genuine FG spare/option part. Only suitable with standard size ball bearings.Dimensions:Length: 10 mmOuter diameter: 11 mmInner diameter: 8 mmContents:2 pieces

€4.90*

Average rating of 0 out of 5 stars

4510 FG Titan Rear lower wishbone pin 6x63mm
Genuine FG spare/option part.Contents:2 pieces

€13.90*
%

Average rating of 0 out of 5 stars

GPM 6079/01 Ball drive wheel shaft for all FG and Mecatech cars, 1 pce.
Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 76.6 mm

From €30.90* €32.90* (6.08% saved)

Customers also viewed

Average rating of 0 out of 5 stars

6034 FG Stiffening brace for Monster-Truck
Genuine FG spare/option part. For all FG monster and stadium models with dual shock front axle.Dimensions:Length: 185 mmDiameter: 10 mm

€12.50*

Average rating of 0 out of 5 stars

6824/07 FG Screw tap M7
Original FG Ersatz-/Tuningteil.Screw tap to cut new thread borings and to recut defective ones.Inhalt:1 Stück

€25.84*

Average rating of 0 out of 5 stars

y4494/03 Sealed bearing f. ball raced servo saver
Seal bearings are robust and keep the dirt from the camps better out than ordinary bearings. This is suitable for the upper part of the servo savers. Bulk: 7 x 14 x 5 mm

€14.90*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Agency