Wide neck flask with 50 ml.The "work of the devil!" The smell is normal! Among others this lubricant is suitable for the following model car applications:Drive shafts (if covered with boots)Transmission in enclosed housings (i.g. ring & pinion gears in Losi 5ive-T or Desert Buggy XL)Differentials which do not use friction padsChesterton® 787 Sliding Paste is a premium quality pure synthetic lubricant that will function effectively even at ultra high temperatures and pressures. Designed for the most severe operating conditions, it provides, through a novel chemical approach, lubrication at pressures up to 10687 kg/cm2 and 538°C.787 Sliding Paste is a unique thixotropic hybrid lubricant. Consisting of a semi-soft paste-like material, this product will flow to fill in small tolerances, yet will keep metal parts separated by the microscopic, symmetric, plates which slide over each other and provide effective lubrication long after the clean synthetic base oil has burned off. Applications for Chesterton 787 Sliding Paste can be found anywhere a need exists for a clinging semi-solid lubricant that will resist water washout and can withstand high temperatures and pressures. Unlike a grease which can turn to liquid and fail under extremely high loads and temperatures, 787 will maintain a slippery film on surfaces and prevent wear, galling and seizure at temperatures unthinkable for a grease. Use in such high temperature applications as lubrication of welding equipment, steel production facilities, smelting factories, forging furnaces, metal casting foundries, around exhaust stacks in power stations, turbine exhaust areas, and any other area exposed to extreme conditions. Because of its excellent resistance to water washout, the product works extremely well in outdoor applications such as on railroad switching equipment and wire rope cables.Composition:Chesterton 787 Sliding Paste is a unique hybrid material that suits the requirements of todays hotter running equipment. It consists of a combination of both organic and inorganic lubricating components and will perform effectively at temperatures ranging from -23°C to 538°C. The geometry of the solid constituents in 787 Sliding Paste is such that they slide over one another and remain undistorted even at the highest pressures parts and equipment are likely to see. The symmetry of the particles means they can withstand extra stresses compared to some inorganic materials which can shatter under extreme loads. The base oil used in Chesterton 787 Sliding Paste is a pure synthetic that will burn cleanly and leave no carbon or varnish to gum up parts and equipment. Because it contains no petroleum oils, it does not present the clean-up problems associated with waste petroleum residues.Features:Pure Non-Carbonizing, Synthetic Base n Lubricates at pressures to 10687 kg/cm n Withstands Temperatures to 538°CExcellent Water Washout Resistance n Non-Fling, Clinging LubricantLow Coefficient of FrictionNSF H2 - Registration number 133956 n No Toxic Heavy MetalsUltra-Fine ParticlesUnique 3 Phase Lubrication PackageApplications:Use in areas subject to extremes in temperature including smelting, forging, metal refining, glass manufacturing, plastics production, and in chemical, petrochemical and power plants, in foundries, around exhaust stacks, on rotary kilns in the cement and mining industry, etc. 787 is specifically designed to provide lubrication for surfaces subjected to extreme pressure. This would include wire ropes, cranes, railroad switch gear, and on large open gears on doors and bridges.Stem nuts, Lead screws, and Linear actuatorsFlange bolts and High tension studs n Press fit bushingsDirections:Brush or pump 787 Sliding Paste into areas needing to be lubricated. Product can be applied by squirt oiler. Spread evenly to thoroughly lubricate all parts and equipment which will see friction.Safety:Before using this product, please review the or appropriate safety data sheet for your area.
2012/502 Brake linkage set dedicated to Mecatech FW01 and FG Evolution.Content:1018/01 Throttle linkage Evo 09 / Comp. 071 x 6534/02 Throttle pivot post for 2 mm linkages 1 x 1018/05 Spacer bushing 5 x 20 mm for throttle linkage Evo 08/5101 x Screw M3 x 18 mm2 x Nut M3
Throttle linkage dedicated to Mecatech FW01 and FG Evolution.Set includes:1 x 1018/01 Throttle linkage Evo 09 / Comp. 071 x 6534/02 Throttle pivot post for 2 mm linkages1 x Screw M3 x 20 mm2 x Nut M3
Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.With steel tongue for infinite adjustment and increased holding power. Especially for high demand applications.Size: 2.5 x 200 mmTemperature range: -40°C to +85°CContent: 20 pieces
Genuine HT spare/option part.Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Specification:Size: 4,8 x 530 mmHolding strength: 25,8 kgTemperature range: -40°C to +85°CContents:20 piece
Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Size: 2.5 x 100 mmHolding strength: 8.1 kgTemperature range: -40°C to +85°CContents:1 piece
Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Specification:Size: 2,5 x 140 mmHolding strength: 18 kgTemperature range: -40°C to +85°CContents:100 piece
Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Specification:Size: 4,8x 360 mmHolding strength: 22 kgTemperature range: -40°C to +85°CContents:50 piece
Genuine HT spare/option part. Extra large bracket with wide surface allows for the use of two strong cable ties at the same time. You can even use a hose clamp at ones own discretion. The bracket comes with M5 lens flange head screw, nut and washer as well as with special temperature resistant cable ties. Content:BracketEach M5 screw, nylock nut and washer4 x temperature resistant cable tie 4,8 x 290 mm
Complete clutch with spring, carrier and bolts.Please note:The usual spare parts supply is not yet available for these engines. Therefore the parts may come from disassembled new engines. Since every single engine is tested at the factory, the parts may show some minor signs of "use".
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).