5179 FG Body set Mini Cooper, red painted 2 mm
Genuine FG spare/option part. Suitable for FG Mini Cooper / Trophy bodies.The set includes:WiperRight/left mirrowsDoorhandleRoof antennaMounting screws for the mirrows
Product information "5179 FG Body set Mini Cooper, red painted 2 mm"
Genuine FG spare/option part.
The body kit consists of the main body part and partial front spoiler.
The body is painted.
The body is fully painted and covered with decals.
The fitting set 5438 is an accessory and is not included in the scope of delivery.
- Mount front: FG 7020/11 Front bumper
- Side body mount front: FG 7012 Body mounts
- Side body mount rear: FG 3014 Body mounts
Rear body mount: FG 7155 Rear body mount
Measures:
- Length: 780 mm
- Width: 392 mm
- Height: 280 mm
- Wheelbase: 510 mm
Contents:
- 1 piece
Login
Alternatives
Genuine FG spare/option part. The body kit consists of the main body part and partial front spoiler. The body is yellow painted. Required body mounts:Mount front: FG 7020/11 Front bumper Side body mount front: FG 7012 Body mounts Side body mount rear: FG 3014 Body mounts Rear body mount: FG 7155 Rear body mountMeasures:Length: 780 mmWidth: 392 mmHeight: 280 mmWheelbase: 510 mmContents:1 piece
Accessories / Spare parts
Genuine HT spare/option part. For all epoxy models, plastic and polycarbonate/lexan body repairs!Direction of use:Use a brush or other applicator. Apply enough Flexa Fix to the damaged area. Be careful not to apply too much in one go as it can be difficult to manipulate. If necessary apply two or three coats to build up the joint area. Use epoxy blanket of pieces of polycarbonate (Lexan) to re-enforce if necessary.You can also use the Flexa Fix to re-enforce the body corners (let the pure product leak into the corners) or to make flexible battery packs.Contents:1 piece / 100 ml
Content: 100 Milliliter (€109.00* / 1000 Milliliter)
Similar products
Genuine FG spare/option part. The body set contents the main part, front body and the rear wing. The body is painted and decorated with stickers. Required body mounts:Mount front: FG 7020/06 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mmContents:1 piece
Genuine FG spare/option part. The body kit consists of the main body part and partial front spoiler. The body is yellow painted. Required body mounts:Mount front: FG 7020/11 Front bumper Side body mount front: FG 7012 Body mounts Side body mount rear: FG 3014 Body mounts Rear body mount: FG 7155 Rear body mountMeasures:Length: 780 mmWidth: 392 mmHeight: 280 mmWheelbase: 510 mmContents:1 piece
Genuine FG spare/option part. The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The thickness of the body shell is 2.0 mm and fits for Sportsline models. The body shell is vac-formed from 2 mm Lexan.Required body mounts:Mount front: Rear body mount: Side body mount front: Side body mount rear: Measures:Length: 890 mmWidth: 405 mmHeight: 240 mmWheelbase: 510 mmContents:1 set
Customers also viewed
Genuine FG spare/option part. The body kit consists of the main body part and partial front spoiler. The body is yellow painted. Required body mounts:Mount front: FG 7020/11 Front bumper Side body mount front: FG 7012 Body mounts Side body mount rear: FG 3014 Body mounts Rear body mount: FG 7155 Rear body mountMeasures:Length: 780 mmWidth: 392 mmHeight: 280 mmWheelbase: 510 mmContents:1 piece
Genuine FG spare/option part. The body set contents the main part, front body and the rear wing. The body is painted and decorated with stickers. Required body mounts:Mount front: FG 7020/06 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mmContents:1 piece
FG body kit Alfa Romeo 156 WTCC made of 1 mm Lexan, painted. The body kit consists of the main body, front body and rear spoiler and is
is red/black, as shown in the photos. The rear spoiler is painted black. The window frames have been painted black and the windows are tinted. There are no side holes drilled in the body and can therefore be fitted to any on-road RC car with a 530 mm wheelbase. Body mounts required: Front part: FG 7020/10 Front bumper Rear carrier: FG 7152/01 Rear body supportFront side: FG 8013 Body support Rear side: FG 7014 Body support Dimensions: Length: 900 mm Width: 400 mm Height: 245 mm Wheelbase: 530 mm Contents
1 piece
Chromed three-chamber tuned pipe system for Carson Wild GP Attack and HPI Baja buggies from the Australian exhaust manufacturer Powerslide Racing. Theres no need for cutting the stock Baja body shell for installation! Unlike many tuned pipe systems which are mounted in the rear of the Carson Wild GP Attack and HPI Baja cars and compromise power output due to the restricted available mounting space, the side mounting of the Riot Stampede allows for an optimized three-chamber system.You can see the Riot Stampede's multi-chamber design in the cutaway model shown in picture 9. The mounting system of Riot Stampede is secured by a tension spring and also provides the necessary flexibility even for jumps. The side mount uses a chromed adapter which is securely bolted to the chassis frame of your car. Set includes: Chromed tuned pipe Header and mounting bracket Complete installation hardware, as well as tension spring and exhaust hose
This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
The first 1/5 touring and sports car designed as a 4WD from the ground up. With a wheelbase of 510mm the 4WD chassis is suitable for the FG Mini Cooper and the FG Porsche GT3 RSR bodies. Equipped with a strong 26 cm³ engine, tuning pipe, tank with quick acting closure, 2 differential gears, front disk brake and a lot more. However, the highlight is still the well-known FG 4WD. Maximum traction, easy handling and grip during cornering as well, these are the advantages only a 4WD model can offer.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version of the car includes servos, transmitter, receiver, rechargeable batteries for transmitter / receiver.The 4WD Sportsline chassis opens up a new era within the Touring and Sportscar class of large scale model cars. Main target was the development of a chassis with supreme driving dynamics and ultimate performance. Maximum traction as well as easy handling, sufficient grip in curves, only a fourwheel powered model offers all these advantages. With the new 4WD Sportsline series FG Modellsport once again sets a trend at 1:5 scale.The 4WD Sportsline chassis for the Mini Cooper is delivered with a wheelbase of 510mm. The fourwheel drive is carried out over an almost wear resistant tooth belt. 2 differential gears, tank with snap closure and a powerful engine with Tuning pipe turn the Sportsline 4WD chassis into a high-class 1:5 scale model with outstanding driving characteristics.You can choose this 4WD model with painted Mini Cooper bodyshell , 2.4 GHz radio control system, servos, batteries in our configurator. Team decals are not included in the delivery content and have to be ordered separately.The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problems. A tank filling enables you to run your model around 45 minutes. Equipment and technical description of the 4WD Sportsline Mini Cooper:Solid 4mm chassis made of high-quality aluminium low-wear belt drive splash-proved 2 differential gears double wishbones at front and rear axle toe-in, castor and wheel camber adjustable at the axles - rear FG ball drive all steel driving components hardened all rotating parts ball-beared servo relieving servo saver front disk brake rear gear brake with big brake disk 700ccm fuel tank with snap closure oil-pressure shock absorbers with volume control and spring adjusting ring 26 cm³ combustion engine with Tuning pipe fabric hollow chamber tires with inserts receiver box and battery holder optional painted polycarbonate bodyshell with decals and with the RTR version the 2.4 GHz pistol grip radio control system with steering and gas servo.Dimensions: Length: 780 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURTouring cars in action!Painting tips:
