5090/01 Mielke Mounting for FG-EVO-Models, Set

€29.90*

Prices incl. VAT plus shipping costs

Available

Product number: m_5090_01

EAN: 4058575034674

Product information "5090/01 Mielke Mounting for FG-EVO-Models, Set"

Item-No.: 5090/1
Mounting for FG EVO-Modelle, Set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

5442/01 Mielke Clutch carrier for 5442

Genuine Mielke spare/option part. Contents:1 piece

€39.90*

TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch

tt_tt1000 Connector: TT1000/01 Universal in - Universal out

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

€39.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

y1041 Angle connector 90° for hydraulic brakes - 1 pce

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

€12.90*

y1042 Angle connector 45° for hydraulic brakes - 1 pce

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

€12.90*

Details

y1040 T-connector for hydr. brake system - 1 pce

T-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

Similar products

Mielke 5099 O-ring 20 x 3 mm , 2 pcs.

Genuine Mielke replacement part.Set with 2 viton o-rings to seal the Masterfix connector from manifold to pipe. Isolates the pipe from engine vibrations.O-ring fits Mielke plug systems and FG #6299. Dimensions:Inner diameter: 20 mmOuter diameter: 26 mmThickness: 3 mm

€3.90*

Mielke Hurricane mounting hardware, 5062, set

Replacement installation kit for the Hurricane system.

€6.95*

Mielke 5500/1 Spare gaskets for Mielke 5500 Tornado-Power, set

Part number: Mielke 5500/1Spare gaskets for Mielke 5500 Tornado-Power, setFive o-rings plus one header gasketDimensions:Thickness: 2,5 mmInner diameter: 20 mm

€8.00*