306044 Smartech aluminum a-arms, front lower, Attack + GasBlaster
Product number:
carson_306044
EAN:
4005299360442
This is the successor of the product:
y1026 HT Aluminum a-arm 2WD, front lower, one-piece
Product information "306044 Smartech aluminum a-arms, front lower, Attack + GasBlaster"
Genuine Smartech spare/option part.
Front lower alloy a-arms, complete with rose joint assemblies included. Fits Carson cars Attack, Super Attack and Gas Blaster
Direct replacement for stock plastic a-arms Carson #32404 or #32546.
Content:
Front lower alloy a-arms, complete with rose joint assemblies included. Fits Carson cars Attack, Super Attack and Gas Blaster
Direct replacement for stock plastic a-arms Carson #32404 or #32546.
Content:
- 2 pieces
Login
Similar products
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.With replaceable bushings for the hinge pins.Fits Comanche, Attack Evo, CRT 2WD, CPT, C5, R5, FG Sportsline and Smartech. Contents:1 piece
Genuine HT spare/option part.With provision to mount a stabilizer bar and replaceable bushings for the hinge pins.Fits Comanche, Attack Evo, CRT 2WD, CPT, C5, R5, FG Sportsline and Smartech Contents:1 piece
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
Machined alloy version replaces the stock stamped part, 5 mm high strength alloy.
clipse_griff Size:
y0264/06 - 6 mm
Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces
Genuine HT spare/option part. Complete set set of all alloy a-arms, one pair of each version.Contents:1 set
Machined alloy version replaces the stock stamped part, 5 mm high strength alloy.
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Customers also viewed
Genuine HT spare/option part.Very strong one-piece a-arm for use with rose joints. Features Igus bushings for the hinge pins (stock hinge pins can be re-used).Rose joints not included!Fits FG Marder, Beetle, Pajero, Off-Road Buggy 2WD and Monster Beetle: Carson / Smartech Attack, Super-Attack und Gas-Blaster! Please note:There are no different a-arms for l/h or r/h applications, therefore the rose joint enters the arm from the top or the bottom depending on the application. Contents:1 piece
The set includes:Item N°.Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1209HT Aluminum front bulkhead A for Carson Comanche, Attack Evo, CRT 2WD + CPTy1210HT Aluminum front bulkhead B for Carson Comanche, Attack Evo, CRT 2WD + CPTy1036HT rose joints with conical spacersUnit prices: 269,00 EURPlease note: the hinge pins are not included, you will use the pins from the stock suspension!Fits on Carson 1/6 / 1:5(Attack, SuperAttack, GasBlaster and Tuareg) and Smartech UNO
The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Crankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Item N° 32403 Upper front wishbone left - 1pce.Attention:These upper a-arms are absolutely identical for l/h and r/h side.They only marked R and L by mistake.
The KRATON® 1/5 8S Speed Monster Truck showcases ARRMA® bashing performance at its biggest and best and in this new ready-to-run version, it's better than ever before. Loaded with EXtreme Bash parts for improved durability, plus a powerful 8S LiPo-capable Spektrum brushless system, the ARRMA® KRATON® 1/5 8S EXB Speed Monster Truck RTR is the ultimate Speed Monster Truck experience for large-scale bashers.The new Spektrum 8S-capable brushless system is more powerful than ever. It features a massive 5687 FIRMA 1100Kv brushless motor, with a huge 56mm diameter and 10% more torque than the previous KRATON® 8S RTR motor. The new motor is paired with a Spektrum S6510 steel gear servo that offers 820 oz-in of torque at 8.4V nearly 50% more torque than its predecessor. The new RTR package also includes a Spektrum FIRMA 160A V2 Smart ESC and Spektrum DX3 3-channel 2.4GHz DSMR radio system with Spektrum AVC® technology built-in to keep the huge power under control.Numerous EXB-hardened parts and options give the ready-to-run ARRMA® KRATON® 1/5 8S EXtreme Bash Speed Monster Truck virtually unstoppable strength right out of the box. They include a 5mm thick EXB 7075 T6 CNC aluminum laser-etched chassis plate; EXB red-anodized CNC aluminum front brace mount; and EXB front bumper with impact-absorbing design. Topping it off is a monster truck body finished with an aggressive new EXB color scheme for a look unlike any other vehicle. No "Candy Crush" designs here the KRATON® 1/5 8S EXtreme Bash Speed Monster Truck is built to be as purposeful as it looks!Adjustable, oil-filled, 20mm bore shocks with 6mm thick shock shafts and ultra-thick composite towers soak up bumps. The KRATON® 1/5 8S EXtreme Bash Speed Monster Truck RTR blasts over dirt, asphalt, and grass all terrain and all conditions. Beefy dBoots® COPPERHEAD 2 big block tires on multi-spoke wheels with durable hubs add all-terrain traction. Everything in the durable design contributes to confident control and responsive handling at high speeds.A center body support, aluminum center braces and composite chassis side pods add more strength. All-metal diff outdrives and gearbox internals, plus durable steel driveshafts, provide a reliable, heavy-duty drivetrain that holds up to extreme, high-speed bashing.ARRMA® keeps your maintenance downtime to the minimum with its proven efficient, easy-access modular design. Considering its performance, convenience, and value, the KRATON® 1/5 8S EXtreme Bash Speed Monster Truck is more than a massive and powerful bashing machine. It's the biggest and best ARRMA® ready-to-run basher to date! EXB (EXtreme Bash) Components)EXB-hardened components throughout its fully assembled chassis give the 1/5 scale ARRMA® KRATON® EXtreme Bash Speed Monster Truck RTR virtually unstoppable strength. Steel TurnbucklesHeavy-duty components including the 8mm thick steel rear turnbuckles and 7mm thick steel steering turnbuckles enable the 1/5 scale KRATON® EXB to withstand extreme off-road bashing. Oil-Filled ShocksMounted on ultra-thick composite front and rear towers and featuring plush shock tuning, the adjustable, oil-filled, 20mm bore shocks with 6mm thick shock shafts easily soak up bumps. High-Traction dBoots® TiresBeefy dBoots® COPPERHEAD 2 big block tires on multi-spoke wheels with durable hubs deliver all-terrain traction and add an aggressive edge to the EXB matte and gloss effect finished truck body. Quick Motor AccessARRMA® holds your maintenance downtime to the minimum with an efficient, driver-friendly design. For example, the easy-access, 3-bolt sliding motor mount allows quick motor removal. Electronics ModuleThe easy-access, molded electronics module screwed to the chassis contains a waterproof receiver box, servo mount and ESC tray ready to protect the electronics from dirt and moisture. Multi-Structured Center Brace SystemMade of rugged anodized 7075 T6 aluminum, the laser-etched 5mm chassis plate includes strong composite chassis side pods and a center body support and brace for maximum durability. Durable Metal ConstructionDurable steel driveshafts plus all-metal diff outdrives and gearbox internals keep the heavy-duty 4-wheel drivetrain rolling over punishing tracks. An EXtreme Bash toughened suspension system smooths the ride. Smart TechnologyThe included Spektrum DX3 Smart transmitter and SRS6110AT AVC® (Active Vehicle Control®) receiver let you take full advantage of the Spektrum Smart Firma brushless motor and ESC's innovative telemetry capabilities. Download the free Spektrum Dashboard App to your mobile device and follow motor RPM, ESC temperature, receiver voltage, drive pack voltage and more data in real-time. Dial-in extra stability with the radio's AVC® system to carve corners and nail jumps without letting up on the throttle. Features The ultimate ARRMA® 1/5 scale RTR Speed Monster Truck Engineered tough with EXtreme Bash 7075-T6 aluminum parts Bigger, tougher shocks, linkages, turnbuckles, and more Aggressive new EXB matte/gloss color scheme Updated, extreme 8S LiPo capable Spektrum brushless power system EXB 7075 T6 5mm thick CNC aluminum laser-etched chassis plate EXB Red-anodized CNC aluminum front brace mount Spektrum FIRMA 1100Kv brushless motor with 10% more torque Spektrum S6510 steel gear waterproof servo with 47% more torque Spektrum DX3 3-channel 2.4GHz DSMR radio Spektrum SR6200A DSMR receiver with AVC® Easy-access front and rear diff module design Updated Spektrum FIRMA 160A V2 Smart ESC with more punch and better driving feel Big Block dBoots® Copperhead 2 tires Front bumper with impact-absorbing design Easy-access 3-bolt sliding motor mount Heavy-duty drivetrain All-metal diff outdrives and gearbox internals Durable steel driveshafts Durable wheel hubs Easy-access waterproof electronics module Center body support and brace for maximum durability Strong composite chassis side pods Wheelie bar High-quality CNC machined aluminum 24mm wheel wrench included
grp_w79 Rubber compunt:
Extra Soft - GWH79X
Item N° GWH79 GRP 1:6 Buggy "GRIP" tire glued, 2 pcs.very aggressive bold x-pattern treadmoderate directional stabilityvery good lateral tractionvery good propulsionfor really loose surfacesTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.