164200RZ FG Sportsline 2WD 510 Wheelbase, Zenoah G230 Engine, incl. RTR

Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.

The V-pin competition tire is particularly suitable for tracks with loose and sandy surface. The high tread profile, extended to the tire shoulder requires a high manufacturing cost. This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. A well proven combination is the use of Mammoth tires in the rear and V-pin at the front. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Please take a look at the corresponding pics:Pic A - very high lateral grip = car tends to oversteerPic B - high lateral grip = still sharp steering responsePic C - reduced lateral grip = neutral handlingPic D - low lateral grip = expect the car to understeerOf course, the before mentioned does depend on the track surface!Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.For very loose soil the soft compound is recommended, under normal condition the medium compound is usually your best choice.Dimensions:Diameter: 163 mmWidth: 65 mmInner diameter: 106 mmPrices of the components:V-Pin tires EUR 39.90 / pairV-Pin tire inserts EUR 9.90 / pairRims FG 6105/01 EUR 14.90 / pairglue set y0067 EUR 13.30Total EUR 78.80Ready mounted and glued EUR 69.90 / pairRim with 18 mm square driveAlso suitable for:With the following wheel adapter: y1183 Rim adapter

Former: "Atego" Truck.The Sportsline 08 quality at a reasonable price for beginners. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 20T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. The models are equipped with a powerful 23 cm³ combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.Dimensions:Length: 880 mmWidth: 435 mmHeight: 380 mmWheelbase: 530 mmTrucks in action!

Original FG spare/tuning part. The following items are required for completion:- E-motor, ESC, steering servo, transmitter system, LiPo drive batteries and charger. The models are built on a 4 mm aluminium chassis with double wishbones on the rear and front axles. All holes in the aluminium chassis for attaching the chassis parts are countersunk from below. The camber, caster and toe-in can be adjusted on the front and rear axles using track rods or adjusting screws with right/left-hand thread. Further equipment points are: Differential gear, smooth-running FG ball drive, oil-pressure shock absorbers with volume compensation and external adjustment ring for the spring preload. All rotating drive parts such as shafts, axles etc. are mounted on ball bearings. The tyres are glued to the rim. Not included : - RC system - 1100 KV brushless motor - 160A controller - Servo- You will also need Lexan paint and a decal sheet.Dimensions : - Length......840 mm - Width.....395 mm - Height.......250 mm - Wheelbase...465 mm

The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Performance Kit from the FW01 is particularly intended for "racer" and differs from the Chassis Kit model by the Performance Kit. Here the list of parts are not including:DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlPerformance Kit :engine brace left and rightfront stabilizer bar 2.75 mm titanium ready for installationrear stabilizer bar 1.75 mm titanium ready for installationthe two 80 gram front weightsthe two smaller 80 gram center weightsWith the Performance Kit the vehicle is quasi equipped as used at races!Stock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us! The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01. The following components are not included in the Performance Kit not and can be selected individually through the choice of options: engine, clutch, exhaust and airbox, differential gear, body shell and wheels. Not included are all relevant components for remote control! included in the kit:clutch bellbell pinionshaft and screw for clutch installationdifferential spur gearnot included:differentialbody shellairboxrear wingengineelectronicstiresclutch We are currently waiting for the latest version of the Mecatech FW01.