The following items are required for completion: body mounts, body.
The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.
Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.
RTR version: Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Radio supplied with 8 stick battery and one charger
Dimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 530 mm Weight 10,2 kg
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 26ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.Dimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 510 mm Weight 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.We deliver the RTR version with mounted and preset radio control system.Dimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 510 mm Weight 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body.This model is based on the Sportsline 4WD chassis modified for drift driving.It features an aluminium engine mount and crown gear, short gear ratio, universal drive shafts, harder suspension, special slick tires.Option parts included : Aluminium engine mounts (large and small) 66215 - 06485/01 Front universal shaft set 68415 Aluminium gear carrier 07439 Steel brake square 06042/05 Drift Wheels 08939Dimensions : Length : 830mm Width : 405 mm Height : 260 mm Wheelbase : 510 mm Weight : 10,2 kgRTR version : Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Transmitter batteries and receiver battery. Charger for both battery types.
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).This model is based on the Sportsline 4WD chassis modified for drift driving.It features an aluminium engine mount and crown gear, short gear ratio, universal drive shafts, harder suspension, special slick tires.Option parts included : Aluminium engine mounts (large and small) 66215 - 06485/01 Front universal shaft set 68415 Aluminium gear carrier 07439 Steel brake square 06042/05 Drift Wheels 08939Dimensions : Length : 830mm Width : 405 mm Height : 260 mm Wheelbase : 510 mm Weight : 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body.The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.RTR version: Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Radio supplied with 8 stick battery and one chargerDimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 530 mm Weight 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).This model is based on the Sportsline 4WD chassis modified for drift driving.It features an aluminium engine mount and crown gear, short gear ratio, universal drive shafts, harder suspension, special slick tires.Option parts included : Aluminium engine mounts (large and small) 66215 - 06485/01 Front universal shaft set 68415 Aluminium gear carrier 07439 Steel brake square 06042/05 Drift Wheels 08939Dimensions : Length : 830mm Width : 405 mm Height : 260 mm Wheelbase : 510 mm Weight : 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 26ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.Not included : Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Radio supplied with 8 stick battery and one chargerDimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 530 mm Weight 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.Dimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 530 mm Weight 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body.This model is based on the Sportsline 4WD chassis modified for drift driving.It features an aluminium engine mount and crown gear, short gear ratio, universal drive shafts, harder suspension, special slick tires.Option parts included : Aluminium engine mounts (large and small) 66215 - 06485/01 Front universal shaft set 68415 Aluminium gear carrier 07439 Steel brake square 06042/05 Drift Wheels 08939Dimensions : Length : 830mm Width : 405 mm Height : 260 mm Wheelbase : 510 mm Weight : 10,2 kgRTR version : Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Transmitter batteries and receiver battery. Charger for both battery types.
Genuine FG spare/option part. The following items are required for completion: body mounts, body.The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.RTR version: Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Radio supplied with 8 stick battery and one chargerDimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 510 mm Weight 10,2 kg
Genuine FG spare/option part. The following items are required for completion: body mounts, body.The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 26ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.RTR version: Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Radio supplied with 8 stick battery and one chargerDimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 510 mm Weight 10,2 kg
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 23ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.We deliver the RTR version with mounted and preset radio control system.Dimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 510 mm Weight 10,2 kg
Carson Drift Attack 2.0 special equipment with 60 mm wide front and rear Narrow-Grip tires!The off-road tire for sandy surfaces and spectacular drifts!With the Carson Wild Attack almost everything for driving (!) is included! The only exception: The fuel mixture from the gas station. (Recommended oil for mixing: y0813/02).The model includes the completely installed 2.4 GHz remote control, incl. transmitter alkalines, as well as a fail-safe system (automatic engine cut-off in case of possible malfunctions!), 20kg throttle servo and 35 kg steering servo, as well as a 2.000 mAh 6V receiver battery with charger and a tool set. Furthermore a spare air filter element and a special mixing canister. A detailed multilingual manual is also included. At the end of the Page you will find an excellent, about 7 minutes duration introduction video to the Carson Wild Attack, which allows even the absolute novice for RC-Carswith combustion engine, the uncomplicated, problem-free entry: Technical details: approx. 70 km/h top speed0 - 70 km/h approx. 2.5 seconds With one tank of gas (700ccm) approx. 40 minutes driving time26cc engine, with pull starterSound reducing tuned pipe exhaust system2-shoe cltch with steel clutch bellA steel differential.Aluminium shocks, dust protectedDrift equipment F+H 60 mm widebead-lock rims with off-road tyresaluminium rim driveradjustable rear wingCompletely ballraced 2WD drivetrain Water protected receiver boxventilated double disc brakealuminium chassisFor driving, only the 2-stroke oil is needed for the fuel mixture.
This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
Genuine FG spare/option part. The following items are required for completion: body mounts, body.This model is based on the Sportsline 4WD chassis modified for drift driving.It features an aluminium engine mount and crown gear, short gear ratio, universal drive shafts, harder suspension, special slick tires.Option parts included : Aluminium engine mounts (large and small) 66215 - 06485/01 Front universal shaft set 68415 Aluminium gear carrier 07439 Steel brake square 06042/05 Drift Wheels 08939Dimensions : Length : 830mm Width : 405 mm Height : 260 mm Wheelbase : 510 mm Weight : 10,2 kgRTR version : Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Transmitter batteries and receiver battery. Charger for both battery types.
Genuine FG spare/option part. The Set contains the front body, the main body, the spoiler-set and the body screws. The body shell is vac-formed from 2 mm Lexan.EFRA number: 5052/06The set is delivered not painted. The body is not drilled and fits all fabricate.Required body mounts:Mount front: Rear body mount: Side body mount front: Side body mount rear: Measures:Length: 885 mmWidth: 392 mmHeigth: 260 mmWheelbase: 530 mmContents:1 piecePainting tips:
€199.95*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).