The offroad tire combination!V-Pin front and Mammoth wide tires in rear are the unbeatable combination for offroad use.combi set:Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EUROffer price: 99,99 EURDescription for V-Pin tires:The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.Diameter: 163 mmWidth: 65 mmPrices of the components V-Pin:V-Pin tires EUR 39.90 EUR / pairV-Pin tire inserts EUR 9.90 EUR / pairRims FG 6105/01 EUR 14.90 EUR / pairglue set y0067 EUR 13.30 EUR Total EUR 78.80 EUR Description for Mammoth tires:Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. Diameter: 165 mmWidth: 80 mmRim with 18 mm square driveThe Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! Where other tires spin helplessly the Mammoth provides serious traction. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Combination for the HPI Baja and 5T cars will the rim extension rings glued on the inside!Unit prices Mammoth:Mammoth tires extra wide: 47.20 EUR / pairMammoth inserts extra wide: 9.90 EUR / pairgenuine FG wide track rims 6105/01: 14.90 EUR / pairgenuine FG rim extension rings 6436: 14.90 EUR / pairmounting + glueing rims / extensions / inserts / tires: 13.00 EUR Total: 99.90 EUR Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EURIntroductory price: 99,99 EUR Also suitable for:With the following wheel adapter: y1183 Rim adapter
In order to achieve a neutral driving performance we recommend to start with harder front tires and soft tires for the rear. If the model understeers in curves use a softer front tire or a harder rear tire. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Durchmesser x Breite / diameter x width 120 x 65 mmRim with 18 mm square drive
TAMIYA PS = Polycarbonate spray paints are specially developed for painting unpainted kit body shells. Numerous colour shades are available and allow the individual design of models. Each can contains 100 ml of highly opaque paint, which is oil and fuel resistant, allowing the use on nitro models.The body shell should be degreased and cleaned before use. Best painting results are achieved when thin layers of paint are sprayed on from a distance of approx. 30 cm. Between two spraying processes the paint should dry slightly to avoid "tears".Always follow the painting instructions of models and on the can. Danger warnings: H222 Extremely flammable aerosol. H229 Container is under pressure: may burst when heated. H315 Causes skin irritation. H318 Causes severe eye damage. H335 May cause respiratory irritation. H336 May cause drowsiness and dizziness. EUH066 Repeated exposure may cause skin dryness or cracking. Content: 100 ml spray can with spray headPainting tips:
With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required. Incl. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm